AWM290L2 Amana Washer - Instructions

Although the Maytag website no longer had a repair manual in their database, I was able to locate one fairly easily online. After removing the motor/washer pump, it was easy to remove the 3 screws holding the washer pump to the motor. Unfortunately, it turned out the motor hub shaft had corroded and removing the pump needed some ... persuasion. Patience and a rubber mallet eventually separated the water pump from the motor. Re-installing went quickly and, so far, no leaks and the washing machine has not started walking across the floor.

Removed the tension spring from the belt retention belt, removed the belt from the large pulley in the back of the washer, removed the 4 bolts holding in the motor and washer pump, removed wiring harness, disconnected the inlet and outlet hoses from the pump and pulled out the motor and the washer pump. Turned the motor over and using the Torx driver (#20) removed the 3 bolts holding on the pump. Gently wiggled and pried the washer pump off of the motor, replaced the pump and tightened down the Torx bolts carefully so the pump didn't crack or break it is just plastic, but had to be sure the pump was seated tightly so the pump would fit back into place and also so it wouldn't leak, after making sure it was tightly attached I reversed the process to put it back together.

The hardest part was removing the tub from washer by myself. I simply removed the bolts holding the sides to the bottom of the unit and lifted it straight off. Be careful when you remove the springs from the drum so they don't spring back and puncture the drain line. Thank you RTV gasket maker. Once the drum was free from the base, i tilted the drum back exposing the pump housing. I used a pair of pliers to remove both drain lines then removed the 3 hex screws freeing the pump. I had no problem removing it from the motor shaft, it slipped right off. I put everything back together as easily as it came apart.

The new hose was exactly like the one I removed. It was simply a matter of putting the new hose through the back, replacing the hose clamp, take the piece off the old hose that makes the bend in the hose to go in the wall drain. Replace the lower front panel with two screws and I was done.

You tubed this procedure and it took 20 min.

First thing I did was to read the great information from other customers. John from Milton's post titled "frayed v belt" was excellent; so was Joseph from Goldsboro NC under the Pump part posts. I would add the following info which wasn't readily available. The Torx/starbit size mentioned in the posts referenced is a T25 the Amana lw8203w2 I have. I bought a t25 size torx wrench at my local hardware store for $2. I got everything together --the belt took some arm strength for an amateur like me to get on. Also, would recommend gloves as some of the edges are sharp down there. Everything appeared okay and when I started the spin cycle it started then cut off. I thought maybe besides the fan belt there was electronics faulty. However, I found an amana repair guide for my model online at scribd and under the troubleshooting section, it described the cutout of the spin cycle and if the new fan belt is too tight, it will bind and the spin cycle will cut out. So I opened up the front again and worked the belt for several turns to "stretch it" and voila, it worked perfectly.

Removed old hose, drained the water from the hose. Put new hose on.

remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor

I purchsaed a new water valve and it was very easy to install. I hate to do thos kind of repair but it went very smooth. Took maybe a half hour, and now it works like new.

Removed the back plate. Disconnected the inside water hose. Unplugged the electrical contacts. Pulled out the old valve, connected the water hoses to the valve, plugged in the electrical contacts, reconnected the inside water hose, and put the plate back on the washer. The hardest part was putting the plate back on the washer. This entire repair would have been exceptionally easy except that I had to sit on top of the washer and hang upside down to do the repair due to the extremely small space the washer was in.

Unplugged washer, turned water valves off, disconnected water lines from washer with adjustable channel-lock wrench. Water inlet valve was mounted on its own plate that needed removed using a screw driver. Disconnected the electric sensors and disconnected the outlet hose. Valve had to be taken off the mounting plate with a nutdriver. Replaced valve and reconnected everything. Water pumped in 10 times faster.

detached 2 inlet/ oulet hose/ hose clamps.removed the 4 motor/ pump base screws, tilted motor/ pump assembly and pulled from washer. Removed the 3 pump housing screws, removed pump/ old drive belt. installed new drive belt, pump, reattached pump screws, motor/ pump base screws, reattached hose/ hose clamp. Rreplacement of parts took approxmiatley 30 minutes.