NTW5200TQ0 Amana Washer - Instructions

We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way

I loosened two screws which held the knob panel in place. I undid the two clips holding the cabinet and removed it. The pump has two clips holding it on, I removed those and the pump came free. Taking advice from these forums, I did not remove the hoses attached. I disconnected the wiring harnesses from the motor. The motor has 2 clips also, these being held on with screws. I removed the screws and the clips. THE MOTOR IS HEAVY.
You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased.
The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached.
Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!

Removed control assembly found lid switch. Had to unscrew ground wire from warsher popped clip on old switch came right out. Had to play with lid in order to remove. Popped new switch in screwed ground wire. Reinstalled control panel,plugged in and the way it went. Trouble shot with parts direct made it easy and saved me 350 dollars(new washer)

Being female & never working on appliances, it was a challenge for me. I took the spinning unit apart: 1) Outer cap 2) Inner cap 3) Screw, nut & bolt popped out. Rusty & wouldn't lock into place anymore. Ordered nut & washer at about $10 + shipping. Total $17 from MayTag Rec'd right at 7 days via USPS. Used nutdriver/wrench to screw in new bolt w/washer. Wah la! That did it! Washer working great now! Now that I'm a "diy" handy person, I'm ready for my next challenge. Hopefully, none!

Ordered and replaced the sensor. Fairly simple. Washer runs good now. Thank you!

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

leaned washer back on wall at or more than 45degree undid two screws off of motor. pulled old part off put new on reinstalled motor Done

I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place and the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story

Repair went well and relatively easy, but did not fix the problem.
Suspect timer switch was the culprit. Nothing was clogged or plugged
up. Water pump and impeller were free and clear with no damage
or leaks.

Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. The hose clip could then be tightened without deforming the hose. Worked great with no leaks.

1. Removed back panel.
2. Removed Entire control paned, control and switch units disconnecting wiring assembly from motor.
3 Tilted front and side panel assembly away from frame, tub assembly and motor transmission assembly.
4.Removed cap from top of agitator, removed bolt holding agitator. Removed agitator, this part was tricky since some corrosion on shaft made agitator very difficult to pull off.
4. From bottom of unit disconnected motor/transmission unit from wash tub.
5. Located clutch assembly and removed lock washers. Removed clutch and replaced with new one.
------------------------------------------------------------
Steps 1 thru 3 were unnecessary.
All that needed to be done was to removed the agitator assembly. then turn unit on it's side or back and removed motor and transmission from the bottom.

I went to Youtube, looked up motor coupling repair for a Kenmore/Whirlpool washer. Chris Fix had an easy to follow video. I tilted the machine back, propped it up. Removed four clips holding two parts in place. Replaced the faulty coupler, Set the engine back in place replaced the clips, and was finished for a total price of $18.

Hello the installation was real simple I first uplug machine from wall I turn off all water leading to in to the machine I then tip machine on it side I then took loose all wiring leading to the motor then motor is held up with 3 screws and 2 bands that hold it in place I reinstall the new motor coupling insert the wires and turn back on the water leading to machine then plug machine back in, every thing was good to go. . . . Save a lot of money doing it my self so simple to do. . . .

Unpluged washer. Turned washer on its side, unpluged wire harness to motor. Removed hoses to pump on motor, removed screws and nuts holding motor, then pulled out motor. Popped off old couplings,intalled new, reassembled. Piece of cake!

After flipping the washer on it's side snap off the clips that hold the motor in place and discard the old coupling. The new coupling fits in very snug some may need a little persuation to attach but once attached the motor lines up nicely and just snap back the clips, turn the washer over and test with a fresh load.