ALW210RMC (PALW210RMC1) Amana Washer - Instructions

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Since the agitator and bell housing seperated as once piece from the drive shaft I didn't have to remove them and the schematic showed how the agitator snapped on to the bell housing and the parts I needed for the fix. The new seal went on with no problem, I just used some of the supplied grease on the tight spots. The hardest part was attaching the bell housing. It came to within an inch of the top of the shaft with no problem with a rubber hammer. But the top screw shroud broke when I tried to hammer it the rest of the way using a wood dowel and a block of wood. I couldn't even get the threads of the supplied screw to even touch the drive shaft. So I bought a longer (1 inch) cap screw from the hardware store and added a washer and suplied ring. After torqing it to 5 ft-lbs instead of the 10-20 the plastic beneath the screw was looking kind of thin and stressed and I was afraid of it breaking through or the screw snapping off in the shaft, so I left it alone and used some silicone caulk to seal in the plug that goes in on top of the screw since the side of the shroud broke off. I slipped on the agitator and am testing a load now as we speak. If I get ten more years out of the washer it will definitely be worth the $100 in parts and shipping !

Although the Maytag website no longer had a repair manual in their database, I was able to locate one fairly easily online. After removing the motor/washer pump, it was easy to remove the 3 screws holding the washer pump to the motor. Unfortunately, it turned out the motor hub shaft had corroded and removing the pump needed some ... persuasion. Patience and a rubber mallet eventually separated the water pump from the motor. Re-installing went quickly and, so far, no leaks and the washing machine has not started walking across the floor.

removed motor removed belt replaced belt,spring,idler wheel, slid back motor in 4 bolts,plug in motor, run good on test run

Replaced water inlet valve with the water inlet valve kit. We ordered it on Monday morning. The part arrived the next day, Tuesday. New inlet valve was put in on Wednesday. It took less than 15 min., and my washer was working! Very impressed!

Removed the tension spring from the belt retention belt, removed the belt from the large pulley in the back of the washer, removed the 4 bolts holding in the motor and washer pump, removed wiring harness, disconnected the inlet and outlet hoses from the pump and pulled out the motor and the washer pump. Turned the motor over and using the Torx driver (#20) removed the 3 bolts holding on the pump. Gently wiggled and pried the washer pump off of the motor, replaced the pump and tightened down the Torx bolts carefully so the pump didn't crack or break it is just plastic, but had to be sure the pump was seated tightly so the pump would fit back into place and also so it wouldn't leak, after making sure it was tightly attached I reversed the process to put it back together.

Just as everyone else explained, disconnect power and water supply, lift top of machine to get to part, disconnect old part and replace exactly with new, hook water and power supply back up and you're done. I was pleased and proud to have done it under 30 minutes (girl power!!) and that included start to finish.

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.

My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.

remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor

I read everyone else's stories and tried this for myself. I am by no means a handy person. This was extremely easy and took me about 10 minutes. I would suggest to everyone to try this for themselves if they have the same problem as I did. Anyone can do this.

You tubed this procedure and it took 20 min.

The new hose was exactly like the one I removed. It was simply a matter of putting the new hose through the back, replacing the hose clamp, take the piece off the old hose that makes the bend in the hose to go in the wall drain. Replace the lower front panel with two screws and I was done.