ALW540RMW (PALW540RMW0) Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Palatine, IL
- Parts Used:
- WP27001007
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
V-belt replacement
Replacing the spin belt is like the others have said, but I'll add a couple of cautions. Don't try to separate the driven pulley on the water pump from the pump shaft. Instead, separate the water pump from the driven pulley. And, make sure you know the routing of the belt for reassembly, because it has to go between the correct legs that support the water pump. Get it wrong and you'll have to start all over. I pulled the machine away from the wall by about 18" and put a block of wood under the front of the machine to raise only the front to 9" or 10" off the floor which made it easier to do the work. Try and take a digital photo of the belt routing from a couple of angles before beginning. Don't forget to route the belt around the tensioner pulley.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from Naperville, IL
- Parts Used:
- WP27001007
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Original belt broke (due to age)
Basically you have to remove the drive motor and pump (in that order). This allows you to get the belt around the drive motor pully wheel. It took me a few tries to get the belt routed right. I assume that if you know what you are doing you can complete this in under an hour. It took me about 4 hours, though - cause I didn't know what I was doing at first. Hehe.
Hope this helps.
Hope this helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Virginia Beach, VA
- Parts Used:
- R0131578
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Could not get adequate amount of cold water
Replaced the mixing value using the kit purchased from PartSelect. The instructions with the kit plus the installation tips found on their WEB Page were extremely helpful. Everything went as predicted except I had to cut and insert a new piece of wire on the white wire between the hot and cold electrical connections. I used two crimp connectors to lengthen the wire. This was a very simple job for a 73 year old man like me. Thank you for the tips and quick delivery of the mixer value kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Pembroke Pines, FL
- Parts Used:
- R0131578
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
hotwater was coming out slow to fill the was tub of machine
removed both hot and cold fill lines and front of washer panel. removed screw holding mix valve plate t the back of the washer . Unpluged connections to mix valve and replaced valve. ( note removing the top of the washer is needed and can only be done by first removing the front by sliding a thin screw driver between the top and front panel to release the clips at the ends.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lizandra from Roxbury, MA
- Parts Used:
- 205217P
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Washer pump was leaking water
Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bel Air, MD
- Parts Used:
- WPW10121334
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Clanging of dryer when rolling
Followed video on PartsSelect website, they made it real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Swanton, OH
- Parts Used:
- WP40094201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Water leak
Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Inlet, NY
- Parts Used:
- WP27001007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Wrench set
drum quit turning
Removed front lower panel, removed 4 bolts holding motor, removed water hoses draining water into a pot, unplugged electrical connector on motor, removed motor, removed water pump from motor (torex bit), separated pump from motor. installed belt reassembled washer in reverse order. To my surprise, it worked and was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Adrian, MI
- Parts Used:
- 40002101W
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
We misplaced the fabric softener dispenser.
We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.
Was this instruction helpful to you?
Thank you for voting!
pump leaked, water valve didn't have cold water
disconnected valve replaced with new, real easy. I removed motor and belt ,4 bolts, than removed 3 star screws from pump, replaced pump and replaced unit. Worked great!!!
Delivery of parts was faster than promised, standard shipping.
Delivery of parts was faster than promised, standard shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Euless, TX
- Parts Used:
- 205217P
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
washing machine pump repair
I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Homestead, FL
- Parts Used:
- 205217P
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washing Machine was leaking.
First, I removed the screws, then removed the pump. I, then, installed a new pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Shelbyville, IN
- Parts Used:
- 205217P
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
pump was leaking and slotted end of drive was split
removed sheetmetal screws hilding motor bracket loosened hose clamps on both hoses and removed hoses., rmoved 3 screws holding the pump in and slid pump off of shaft. installation was reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Gibbon, MN
- Parts Used:
- 205217P
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The discharge pump wasleaking
I removed the 4 bolts that hold the drive motor in place, then tipped the motor on it's side and removed the 3 allen screws that hold the pump in place. Then just reversed the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from mercerville, NJ
- Parts Used:
- WP27001007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
drum not spinning fast enough . still wet long time in dryer
tilt the washer back removed bottom panal .removed bracket holding motor took motor out removed 3 scewer holding pump. took belt off put new one on. about 45 mins pretty easy job
Was this instruction helpful to you?
Thank you for voting!