LW8203W2 (PLW8203W2 B) Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nick from Oceanside, CA
- Parts Used:
- WP34963
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A small leak into the tub
1. Removed the hot and cold water hoses. 2. Undid one screw holding on the solenoid mounting plate. 3. Pushed the plate in at the top to unlatch the plate at the bottom. 4. Pulled the plate out and undid the output hose. 5. Replaced the solenoid assembly held on by two screws. 6. Replaced it all in the revers order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from BAINBRIDGE IS, WA
- Parts Used:
- WP40053901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Cracked hose leaking
Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Lou from NEW ULM, MN
- Parts Used:
- WP40053901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
The hose on the washer been leaking and needed to be replaced.
After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bel Air, MD
- Parts Used:
- WP233520
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Clanging of dryer when rolling
Followed video on PartsSelect website, they made it real easy.
Was this instruction helpful to you?
Thank you for voting!
Pump leaking. Replaced aging belt.
Removed front cover of machine. Removed motor/pump assembly which was held in by four (4) bolts. At the same time removed belt from transmission pulley. Removed pump assembly from motor, held in by three (3) torx fasteners. Before installing new pump installed new belt on motor assembly. While setting the motor/assembly in place threaded belt around transmission pulley. Fastened motor/pump assembly. Very easy process!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Glen Allen, VA
- Parts Used:
- WP34963
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Slow fill on cold cycles.
The repair was easy. It took approximately 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lizandra from Roxbury, MA
- Parts Used:
- 27001233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Washer pump was leaking water
Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theo from flemington, NJ
- Parts Used:
- 31239
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Timer Was Not Engage To Turn Washer On To Wash Sycle
Took the timer nub off by unscrewing then the cover housing the timer unit . 6 Screws . 3 In front 3 in back . Cover came off easy. Un plug the power. Disconect old timer and replace with the new . Plug comes off easy by gently puling it out . Put back cover put back timer nub plug the power on and there it was back as new.
Was this instruction helpful to you?
Thank you for voting!
Was leaking water
Just took it apart and figured out what was leaking. Ordered a piece online through Partselect. Got the piece in 2 days and put it back together. Went real smooth, saved us from buying a new washing machine. Thanks! My husband is quit the handy man too! So I thank him too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Homestead, FL
- Parts Used:
- 27001233
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washing Machine was leaking.
First, I removed the screws, then removed the pump. I, then, installed a new pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Euless, TX
- Parts Used:
- 27001233
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
washing machine pump repair
I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIke from Otsego, MI
- Parts Used:
- 27001233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Water Pump Leak
I removed the front lower panel. I disconnected the springs holding the motor to the chassis. I removed the belt off the pump pulley. Pay attention to the way the belt runs from the pulley and through the pump. This will aid in placing the pump back on so the belt runs correctly. Disconnected the wires, removed the capacitor bracket so I could take the motor/pump unit out after I removed the 4 bolts holding the motor/pump unit. Removed the 3 torx screws holding the pump to the motor. Matched the new pump to the old to make sure the new one was correct.
Installed in reverse order.
Installed in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Rancho Palos Verdes, CA
- Parts Used:
- 27001233
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Water leaking from pump seal
Unhooked the idler pully spring, removed the 2 hoses from the pump outlets, unhooked the idler pulley srring to slaken the drive belt tension, removed 4 bolts from the motor mount to drop the motor, and slipped the drive belt off the transmission pulley.
Removed 3 torx screws that secure the pump. The pump was stuck to the motor motor shaft from corrosion and had to knock the pump off with a hammer. Reassembly was a breeze.
The most serious problem I had was a black widow spider lurking under the transmission pulley. Never did get it!
Removed 3 torx screws that secure the pump. The pump was stuck to the motor motor shaft from corrosion and had to knock the pump off with a hammer. Reassembly was a breeze.
The most serious problem I had was a black widow spider lurking under the transmission pulley. Never did get it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Gibbon, MN
- Parts Used:
- 27001233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The discharge pump wasleaking
I removed the 4 bolts that hold the drive motor in place, then tipped the motor on it's side and removed the 3 allen screws that hold the pump in place. Then just reversed the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Shelbyville, IN
- Parts Used:
- 27001233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
pump was leaking and slotted end of drive was split
removed sheetmetal screws hilding motor bracket loosened hose clamps on both hoses and removed hoses., rmoved 3 screws holding the pump in and slid pump off of shaft. installation was reverse
Was this instruction helpful to you?
Thank you for voting!