LWM205AC Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from Clearfield, PA
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Water leak
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from FACTORYVILLE, PA
- Parts Used:
- WP35-2044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hinge Broken
Removed screw, replaced hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marilisa from naples, FL
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
loud grinding sound then washer would shut down then there was water all over
first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Palmdale, CA
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water removal pump stopped working.
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hole at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert E from Katy, TX
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Whasher would not drain
Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from New London, OH
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old belt broke and fell off
tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LEXINGTON, KY
- Parts Used:
- WP35-2045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken lid hinge pins
I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from OXFORD, NY
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn belt
Rolled the old one off and rolled the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from WATSON, MN
- Parts Used:
- WP21001915
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Tub to pump hose worn out and leaking
Replaced the hose. two clamps and retainers. very basic repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from LIVINGSTON, MT
- Parts Used:
- WP35-2045
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Hinge Pins
I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hinge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sonya from VAIL, AZ
- Parts Used:
- WP43-0057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Activator device broken off
Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from East Brunswick, NJ
- Parts Used:
- WP35-2045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lid hinge pin broken
Opened hinges top of washer. Removed screws holding hinge bases. Removed the washer top lid and unscrewd broken hinge pin. Replaced hinge pin and inserted in pin base and screwd base op hinge back onto washer and job was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILL from DIX, IL
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The Pump Went Out & Water Was All Over My Floor..
Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .
Was this instruction helpful to you?
Thank you for voting!