NFW7200TW10 Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tracy from Danville, CA
- Parts Used:
- WP34001340
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Washer would not drain nor spin
My husband read on the Internet how common this problem is and how easy we could do it ourselves rather than pay the service etc.... While reading there was a link for Part Select. We simply found the part with-in minutes and ordered. They have PayPal so I basically ordered it in less than 1 minute, emailed my receipt and DONE! We selected overnight shipping because the laundry was piling up - we received the part less than 24 hours and I was up and running before dark! PERFECT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Holbrook, AZ
- Parts Used:
- WP34001340
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Odd noise when the spin cycle started, water would not drain, D5 error.
The washer comes up with the D5 error if either the door is not shut correctly, or it can not detect that the washer is drained. I had to put the washing machine on its side to access the bottom. There is an access hole that you can get the pump from. I unplugged the pump, then removed the bolts to take it out. The pump comes apart with a few screws removed. I saw that the magnet inside was broken in half. Putting a new pump back in solved the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Greenfield, MA
- Parts Used:
- WP34001324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drain pump runs continuously
Checked owners manual for diagnostics. Pointed to door lock mechanism, so we replaced. didnt work. Went online to Just Answers.com, chatted with pro named Mike(for the fee of $25) and without getting full description, he told me to replace pressure sensor. Bought one here for $50, replaced it, and still the problem lingered. Called a real Technician to the house, for $90, and he spent 4 minutes looking and tapping, and voilla, it worked. Turns out it was a stuck relay on the control board, and the tapping loosened it. He told me I may have trouble with it in the future. If so, I would buy one here. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Bismarck, ND
- Parts Used:
- WP34001340
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
I was getting an "nd" error code with every wash cycle.
I removed the back service panel and checked the drain hose for any debris and checked the connection from the tub basin to the drain pump. I then check the drain pump and noticed the impeller blades were a bit worn. After the new drain pump arrived, I did have to swap the old intake housing with the new one in order for the whole thing to mount to the shock-absorbing mounting plate. Reconnected both hoses and the electrical connection and everything ran great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Charleston, SC
- Parts Used:
- WP34001131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hot water would not shut off when wash temperature selected was hot or warm.
Disconnected power cord. Shut off water supply. Disconnected hot water supply hose. Removed top cover. Disconnected appliance connection to Hot Water Control Valve. Removed screws holding HWC valve. Removed existing HWC valve. Installed new HWC valve. Reconnected appliance connection. Reconnected water supply hose. Turned on water to check for leaks. Reconnected power supply. Started washer with hot cycle selected. Timed water fill time. Replaced top cover. Washed a load of whites in hot water. Installation and test complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricardo from Rockwell, NC
- Parts Used:
- WP34001151
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
it does not do anything. It does not work at all.
I replaced the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shawn from manistique, MI
- Parts Used:
- 34001424
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
outer door was broken at hinge due to someone leaning on it when it was open
I started by watching the repair video on the site. Only tools needed were a phillips head screwdriver and a standard screwdriver. had the whole thing done and operational in about 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Rochester, MN
- Parts Used:
- WP34001260
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
installing new door latch
first of all, I am not at all handy, so that fact that I could do this at all is pretty amazing. I watched the video and it was very good. At first all went smoothly...I got the top off, the control panel off and the detergent drawer out. Then I ran into problems, three of the six screws holding on the front panel wouldn't come out. I sprayed Liquid Wrench on, waited for a while, still wouldn't come off, then I tapped them with a hammer, still wouldn't unscrew. But I was able to access the door latch from the top rather than the side...a little tight and awkward, some swearing was required, but it worked. Machine now working like a charm, yay!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kermit from Laplace, LA
- Parts Used:
- WP34001340
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water pump broke
Remove back panel disconnect hoses clamps with hands, use socket wrench on hex bolts, remove pump use philip screw driver. Install new pump same tools, replace panel stated washer, works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Metairie, LA
- Parts Used:
- WP34001260
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door lever was broken
Used online video which was really good. After changing the lever, I realized I needed to order a new latch because it was broken also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Bensalem, PA
- Parts Used:
- WP8182634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door latch not closing or not releasing
Unplug electric. Open door. Peel rubber bladder back from washer door seal enough to expose wire retension ring. Remove three screws that hold door latch. Remove latch. Remove three wire harnesses. With new latch, reattach wire harnesses. Insert latch. Secure to machine with the three screws. Refit door seal and secure with retension ring. Plug in electric. Done.
Was this instruction helpful to you?
Thank you for voting!