P75751-8W Amana Washer - Instructions

Hi there,
I received the parts from you in short period of time,
take its out 4 screw with screw drivers,
Open the pannel, unscrew one nut with nut driver, take it out Lid assembly
I put it in myself, It worked wonderful,
I do appreciate your service in " Do-it-Yourself" system.

Thanks,

Harry Lin

Un plug machine. Turn off hot & cold water. Remove the front panel by removing the 2 screws at the botton & lift front from the bottom until it unhinges from the top. Tilt the washer back far enough to put a contaner to catch the water left in the hoses. Loosing the hose clamps so the water comes out slowly. If you remove the hose to fast your container won't catch the water. Do one hose at a time. Next disconnect the wiring harnes from the motor. Remove the 4 screws holding the pump/motor. Disconnect the belt from the washer. You will have to tilt the pump/motor to get slack in the belt. Remove the pump/motor & the belt will come with it. This is when I found that the belt was toast & I had to order a belt. Paid shipping twice. once for pump & once for belt. Seperate pump from motor by removing 3 screws. My pump came right off. Reverse the operation to install. REMEMBER TO PUT THE BELT ON BEFORE THE PUMP.

Followed above listed advice on replacing

I saw on internet that it was the lid switch and how to fix it. On this machine I have replaced timer and belts, machine is 22 years old.
A bowling friend of my father, was a Magtag repairman and salesman. For years showed me how to fix my Sears washer and dryer. When he sold me a Magtag washer and dryer, he said it was a great machine.By the way my dad worked for Easy Washer in Syracuse, They invented the spin cycle, ask Whirlpool.
ED

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

Started with removing 4 screws on the top of the control panel. Once open, I found the schematic taped to the top. I traced the wires and found the 2 wires to test. I unplugged them and attached the jumper wire. Turn on machine and it worked. Ordered the part( it came in in about 3 days. First disconnect the power. The micro switch is mounted with 2 screws, remove these and as you disconnect the wires , attach them to the new switch, put it back in place and reattach the screws. Test .

Found instructions at this web site, got part in a couple days, changed Lid Check Switch in 15 minutes, washer was up and running again. Best website for fixing stuff I've seen!

I followed video instructions which were very helpful and getting to the lid switch assembly was not difficult. After putting it on we still had nothing. I noticed there was quite a bit a corrision on the connecters so we cleaned those with fine emery paper, reconnected them and like magic , the washer is back in business. I was very surprised the part arrived about 36 hours after I placed the order and in just a couple of hours at the most we had a working washer again.I've got partselect.com saved in my favorites for any future diy repairs needed.??

First I took the seals out of the box they came in and let them hang on a hanger to get all the kinks out of them for a few days. Then I started at the corners of the refrigerator doors and peeled the old seals off on one door then replaced the seal by using my thumbs pushing at the corners first and once I had all four corners in I worked my way around the rest of the door, After both doors were done I used a hairdryer to expand the seals against the refrigerator case to make sure it seals tight.

I watched the video suggested by Part Select, it was easy to follow. I had first changed the belts because they were worn but that wasn't the problem, the next suggestion was the lid switch assembly which was the answer. This washer was produced in 1989 and works like new again!

At first, I suspected the timer. In the problem solving section of the Maytag owner's manual, there was a reference to the Lid Check Switch, which was the queue I needed. with the help of the electrical diagram, I located the switch,then hotwired that circuit to confirm to myself that it was the switch that was faulty. Overall an easy fix.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Followed video on PartsSelect website, they made it real easy.

I guessed that the lid switch was bad based on internet information that suggested that cause of the problem. I confirmed this by disconnecting 2 wires to switch and taping them together to bypass the switch. Wiring diagram was available. Washer worked that way so I ordered a new switch which arrived within 22 hours, regular shipping.

Replaced the switch. No need for me to add detailed instructions for this simple swap. More than enough descriptions are already collected on the excellent website of this outstanding parts supplier!