ALW410DAW-PALW410DAW Amana Washer - Instructions

Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

So, I finished draining, removed the hose (required pliers to squeeze off a hose clamp).

Upon inspecting the hose, it was also apparent that the hole was caused by rubbing against a support bracket for the motor. This should not happen, but it did because the plastic standoff supposed to keep the hose away from the bracket was installed 180 degrees backwards.

So, I simply replaced the hose and turned the bracket around to the correct orientation.

Everything worked as planned and my repair cost was much less than if I had called someone out.

Unplugged the washing machine and turned off the water to the machine. Removed the two front covers; unhooked the two front springs; removed the (4) motor mounting bolts; unhooked the two hoses for the water pump; unhooked the wiring harness; removed the belt from the driven pulley; pulled the motor assembly out; removed the (3) screws to separate the water pump from the motor; removed the belt from the motor pulley; installed new belt and repeated above in reverse to put everything back together; started washing machine and it worked great.

This is not a bad repair, but give yourself some time. I did not have to take the tranny and motor out, but the inner and outer tub and all related parts had to come out, along with the outer tub base. If you are replacing the tub bearing, you HAVE to order the seal kit. Don't try to skimp like I did, since you will need the seal kit as this is what causes that bearing to fail in the first place. We forgot how quiet the washer was after I fixed it, and it saved us from buying a new washer since we were ready to say the heck with it and buy a new pair. You might need an 1.5 inch socket to get the big nut off the spindle, but I was able to get with a visegrip and hammer. The nice thing about this repair is even if you screw it up, you won't have water all over the place because of the seal design. I just checked under the washer a few times for the first few weeks and all seems fine.

to replace the seals is the easier part of the job. I Removed the front panels and removed the front screws for the top and opened up. Then you have to remove the agitator, then the bell plug, the bolt holding the bell along with the bell, then the 1-1/2" nut under that. then slide the plastic washer that fits into the splne. to remove the drum you have to remove the plastic top to the drum assembly. Then you can remove the drum along with the along with the alumunum splined hud that is atrtached the the metal drum. Before removing the drum the seal under the plastic washer mentioned above needs to be removed. once the drum is out you can in bolt the aluminum splined hub from the metal drum. The outer plastic drum has a seal that is glued and slides over the vertical flange. The glue is not included in the kit. once the botom seal is installed. install the new aluminum splined hub to the metal drum. install lower seal to botom of the splined hub. reinstall the hub. once the large nut and plastic spined washer is installed. The top seal neds to tapped onto the hub agian with an object that matches the dia. of the seal flange. the n install the bell, nut ans plug. The bell does not like to align to the splined shaft, do not force it. reinstall the agitor an assemble the rest.

I first unplugged the washer. I removed the 2 screws that hold the front panel and removed the front panel, they are located at the very bottom outer edges of the front panel.
I then removed 4 of the large springs that are attached to the drum, this washer has six but I only removed the front 4. Removed the two hoses going to the water pump and drain hose, removed 4 bolts that attach the motor to its mounting bracket. Unplugged the wiring harnesses going to motor and what looks like a capacitor mounted to the side of the motor.Then I removed the drive belt. ( when the machine would first start to spin it would make a clacking noise which ended up being a chunk out the the drive belt causing the belt tenshioner to slap causing that noise and letting the drum spin during the wash cycle. So far very easy. I then removed the motor and when it is disconnected you can then remove the water pump. Three hex head bolts need to be removed and it pulls right off. I then removed the six bolts that hold the brake pads in place. I applied silicone grease to the new brake pads and installed them. The pad at the back of the drum was very hard to line up with the holes. I used a very small screwdriver to line up the disc brake mounting holes to get the bolts started and it worked fine. I then put it all back together and it works great. I have to add that I have been an auto mechanic for 28 years and not to brag but this is not your average repair job.

Remove the electrical power plug and disconnect the water hoses at the back. Remove the lower front panel by taking out the two screws at the bottom edge. Then lift out the upper front panel which exposes the two sheet metal screws holding down the top panel. Lift open the top panel and secure it up about 90 degrees so it doesn't flop over backwards. Twine tied to something overhead works fine. Replacement procedure for the valve is obvious, once exposed.

Unplugged washer then took back off control panel. Removed clamp and tube from pressure switch. Pushed in tabs with a screwdriver and lifted top. Removed clamp and broken tube. Put new tube in place and tighten clamp with nutdriver. Closed top and put other end of tube on pressure switch with clamp. Put back on control panel and plugged in. Clamps are to big for application but do work. So far so good!

As the other posting said, it appears our problem was due to constant overloading, as an inspection of the machine with the bottom service panel removed clearly revealed all three milkstool legs broken away from the round center piece. My teen-agers are now aware that I am somewhat displeased about this.
My first action was to order the repair manual. In retrospect, it was only marginally useful as a job aid, but was essential in verifying ID of the part and understanding details of how the machine works. I started by following the manual which said to remove the agitator. The agitiator didn't want to be removed, even after repeated attempts and applications of varying amounts of both physical and vocal persuasion. So, I reconsidered what I really needed to be doing, and dislodging the agitator (and subsequently all of the spline seals) really wasn't necessary. I just needed to get to and replace the crushed milkstool (and leave everything with a seal alone!).
So, Phase 1 - I removed the front panels, and tilted up the top. I then disconnected the power cable to the motor and the inlet/outlet hoses to the pump (more on my haste in this step in a moment...). The wiring harness is held in place on the machine back and milkstool by plastic retainers that release when compressed. I then disconnected the green ground wire, the panel that holds the blue water inlet valve assembly, the black hose on top of the tub and the clear air pressure hose (just pulls straight out of the tub side connector). This allowed the top to be removed and set aside. I then pulled the drain hose through and pulled the plate that holds it in place from the back, then removed all the screws that hold the cabinet to the base, then set the cabinet aside. Next, I disconnected all 7 springs from the base to the tub, and the tub was free. I pulled the tub from the base (not too heavy) and inverted it to get at the motor/pump/milkstool.
Phase 2 - gently removed the idler spring and removed the belt from the pulley. Pulled 10 1/2" self-tapping screws that hold the milkstool to the tub and the motor to the milkstool (these can be discarded as you get new ones with the milkstool). Now pulled 6 screws that hold the brake pads in place, and pulled the brakepads. The manual says to replace the pads whenever pulled, but these didn't look terribly worn, and work just fine after reassembly. The pulley then came off easily, and then subsequently so did the milkstool (with integrated bearing). Reassembly was the reverse of disassembly, and all seemed logical enough until I got to reattaching the hoses to the pump. The manual does not make it clear which one goes where, and I forgot to take a picture of that part of the machine before dismantling. Long story short, I put them on backwards, and you'll probably not be surprised to hear the machine didn't work as anticipated when we turned it on! (wouldn't spin, wouldn't pump out the water and made a nice puddle in the laundry room). Once we ladled out all of the water from the tub and reversed the hoses, everything worked fine. So - words to the wise (1) mark hoses, wires, etc with tape, grease pencil, whatever works for you BEFORE disassembly and (2) take close-up digital pics as you progress.

I removed the front cover to gain access to the motor. I saw that the belt was starting to get chewed up so I removed it. While looking at the schematic on Parts.com I noticed the Idler Pulley Wheel was much larger then one currently on the machine. I ordered that also in case I needed it. I needed it. Once I replaced the belt and the pulley the machine ran better then ever. Originally I thought I just needed the belt but thanks to Parts.com I realized I needed a little more. Thanks.

I searched "sav2655aww repair" (my model number) on the internet, and found people who had the same problem - and did the same repair. Some put up very detailed instructions.
Anyway, with instruction, it was a pretty easy job. Remove the front panels, disconnect the hoses from the water pump, unplug the electrical connector from the motor, remove the 4 bolts that hold the motor mount, and slip off what was left of the belt. To replace the belt, I also needed to temporarily remove the water pump (3 torx screws) from the motor, because the belt snaked in between those two parts. Once replaced, I remounted the motor, slipped the belt over the main wheel (under the tub), set the belt tension wheel to take up the slack, and reattached the hoses and wires. Surprisingly, the belt replacement took care of the noise (the whole unit would sway out and repeatedly hit the front panel during a wash - I suppose it wasn't agitating or spinning correctly). Works like new.

Unplug washer, turn off water supply, disconnect hoses from washer valve(have bucket ready for water remaining in hoses), Remove bottom front panel by unscrewing two hex head screws near floor then pulling panel toward you and down, remove top front panel same as bottom to expose screws securing washer top, lift washer top and prop open or tilt back onto counter(hold washer lid when tilting back). The inlet valve is on the back right. Label and unplug wires, unscrew hose clamp and remove hose, go to back of washer and unscrew plate holding valve and remove. Mount new valve to plate and fasten from back of washer, reconnect hose and wiring, close cover and fasten screws, replace front covers and secure, reconnect water supply hoses(do not over tighten), turn on water and plug in washer.

Brake pad kit does not come with installation instructions even though it says it does. Remove bottom front panel from washer. There are three brake pads. One of mine (the right one) broke into three pieces and was found on the bottom of the washer. This is how I identified what was wrong. Run the washing machine on the handwash extra light cycle (you could use another cycle, I used this one because I believe it is the shortest), there is a point in the cycle where the disk clamping the brake pads separates from the brake pads and allows you to remove and replace the pads. During other parts of the cycle, the disk is clamped onto the brakes and you could not remove or install a brake pad. I removed the two black hose on the bottom right to get to the right brake pad. Have a 2 gallon bucket ready to collect the water if you did run the washer as above. With difficulty, I was also able to reach around the back side of the right brake pad. I used a socket wrench set. I then removed and replaced the left brake pad. I left the rear brake pad in place. I was not able to get to it.

The washer is four years old.
This is the second time I needed to replace this same drain hose on this same washer since I had the machine
There is only my wife ant myself maybe, 2 -3 medium size loads per week - why I would have two drain lines develop the same problem in almost the same location in two years is disconcerting
There must be a design problem with the clear plastic hose - Suggest Maytag go to a thick walled rubber hose
The hole is alway inside the washer on the bottom just after the hose bracket - I suspect that something rubbing causing a small pin hole to develop - when the condition first starts it is very difficult to located -There will be water under the washer
Run the washer and discharge the water - to locate

The replacement must be made through the lower front removable panel - and is easier to do if the pump return hose is also disconnected from the pump

Be very carful with the thin wall replacement hose - very light weight plastic - do not pull across the floor of washer - it could easily get damaged

Your company did a get job getting the part to me - The Fed Ex track system was great
I could tell exactly where the delivery was al all times -

Pulled motor, as the belt will not come off unless you take to water pump off off the motor. Installed new idler wheel, washers, clips and belt. Reinstalled motor.
Works good and hopefully lasts a long time!

Place black rubber adapter on the end of the drain hose and stick in the stand pipe drain. That's all.