ALW880QAW-PALW880QAW Amana Washer - Instructions

Needed part. Ordered Part from PartSelect Friday afternoon and figured I'd get it the following week. No big deal. Part arrived at my doorstep next morning before noon. UNBELIEVABLE SERVICE. Not requested, but it was there. So I fixed the machine as soon as I got it. I wish every company had this kind of service. I've already told my friends. It just can't get any easier than this.

I had some sweaking and then burning followed. I came to find the belt had burnt and stopped my washer from working. Ordered a belt and replaced. Washer worked for one week. Squeaking and burning again. Belt was still intact, thank goodness. Beleive it is another pulley part for the washer. Might order another part. Overall the fix was good, but had another issue.

Sunday night - removed old valve and hose 15 min went online, found & ordered part - 15 min - part showed up Tuesday afternoon, replaced defective valve 15 min - did laundry! Couldn't have been easier or less expensive!

First always unplug appliance.Then I shut off the water.I took the front off the washer.Saw the idler was the problem.Ordered parts and new belt.Removed motor assy,and removed pump.Checked impellors and pump bearing.Installed new parts for idler.Installed belt.Re-installed pump to motor,then re-installed entire assy.Turned on water and ecectricity.Ran complete cycle to test.Re-installed front cover.

Unpluged electric, diconnected dicharge hose from wall drain, disconnected water lines from rear of washer and at wall hose connection, removed lower front panel, removed large front panel, disconnected hoses at motor(put towels at hoses to catch water leakage)THEN-took washer to the garage and tuned up side down. Removed front two tub springs, removed (4) motor bolts, removed electrical harness from motor, remove and replaced new brake pads. NOTE:brake pads need to be somewhat driven(pushed hard) into brake pad slots. Also it was easier to install the rear pad by removing the 4" knock-out at the side of the washer. Somehow reinstall the knock-out to keep mice and animals from entering the interior of the washer. THEN- reinstall all items in reverse order. Any one mechaniclly minded can replace the brake pad. My wife and I saved lots by doing the replacement myself. THE END. Good job Gary Final note:besure to intall the drive "v" belt around the 2" pulley wheel.Very important.

remove agitator then remove center bolt from hub, match bolt with longer bolt so that gear puller will work. install bolt and gear puller and twist top of gear puller until hub is removed. remove old seal ,use sand cloth or emery cloth to remove all deposits from shoulder. make it shinny, use some dawn dishwashing soap to line the inside of the new seal at the bottom and slide into place.take a piece of 2" PVC about 4" long and slide over the top of the seal and tap with a rubber hammer until seal is seated firmly on shoulder. look to see that there are no gaps with a inspection mirror or a make-up mirror.If their are no gaps ,install the hub and tap on the new hub with the rubber hammer. the hub will not seat all the way down so use the old bolt to pull it down, now take out the old bolt and install the new one, this is because the new one has lock tite on it ,your done!

Removed the old hoses and screwed on the new hoses.

1) removed front panels from washing machine
2) removed water pump. Three small torque bit screws and (2) hoses.
3) removed motor (because I realized that the belt tensioner also needed work as it was siezed) removed (4) bolts and an electical connector.
4) repaired tensioner by taking apart and cleaning bearing surface. Needed snap ring plyers to take apart.
5) put motor back in
6) replaced belt
7) put water pump back on
8) intalled front panels back on washer

Removed the motor and mount, removed pump, replaced motor,pump,belt and mount and re-installed. Everything fit and functioned.

I figured that the best thing to do is buy an adapter for the standpipe and now no more overflowing.

First I tried to lift the lid on the top of the washing machine. I eventually realized this model doesn't open up from the top. I removed two screws on the very bottom of the front panel of the washing machine. Then pulled gently downward to release the front panel from the two clips holding it in at the top. Once the front panle was removed, I found I could easily access the drain hose and disconnect it from the pump by loosening the clamp screw. (Be aware, there is still water in the hose and pump that will run out onto the floor; I had a bucket close by and tried to catch most of this water, but its somewhat futile.) There are two additional hose clips one underneath the tub, and one on the back panel of the washer that hold the hose away from other mechanical parts. Once the hose is freed from those clips it could be removed from the washer by feeding the hose out the back panel. The new hose was then inserted and fed down inside the washer, attached to the pump, tighten the hose clamp screw, clip the hose to the other two clamps so it is out of the way of other parts, reattached the front panel and you're done!

One other note about PartSelect.com...A few days after ordering my part, I had an "International Transaction Fee" show up on my debit card statement. I panicked thinking my card number had been stolen only to call my bank and find out PartSelect is based in Canada.

Removed front panel; loosened hose clamp at pump; removed existing drain hose. Easy part.
Installed new hose at pump and tightened hose clamp. Somewhat difficult.
1. Your hose design should be solid flexible rubber hose instead of corrugated type. Had rough time snaking hose to the pump.
2. Your future designs should have rubber hose or hard piping to the exit hole on the back panel and terminated in a male fitting, then connect flexible hose from fitting to drain line. Similar to "hot & cold " water connections.
3. For future customers- care should be taken installing the "black" portion ; it kinked on me 2 or 3 times because you have to keep rotating the entire hose to keep the "black" portion straight.

this machine seems good to work on because almost every thing is done from the front without pulling it away from the wall. Removed front lower cover by removing two screws. There are three brake pads with two bolts each. applied silicone grease to each pad and put it back togather

I had to take the entire tub assembly from the machine to replace the milkstool which had been crushed by the weight of over-loading the washer. It took about 2 & 1/2 hours to complete the job, but it was well worth the effort to save the expense of replacing the appliance. Part Select provide the right part as promised and saved me a lot of money. Thank you for your service.

It was so simple I don't think I even need to explain. Couple of screws in and out and done. Saved big money by doing the repair myself...I was surprised how quickly the part arrived. I was able to access from the back of my machine. Did not have to remove the top. Very easy thanks