CW4202W2-PCW4202W2A Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary Lou from NEW ULM, MN
- Parts Used:
- WP40053901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
The hose on the washer been leaking and needed to be replaced.
After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Amarillo, TX
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken prong
I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEAN from KINSTON, NC
- Parts Used:
- W10169313
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door would not cut the machine off when it was opened.
Installed the new part. Worked great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from ANAHEIM, CA
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door switch was defected
The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEROME from NILES, IL
- Parts Used:
- W10169313
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch clip broke
Unscrewed front panel. Pulled off unbroken wire connecter and popped switch and put new one in. Replaced front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from NEW ROCHELLE, NY
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door switch broke
Just follow the video. The hardest part is getting the top to disengage from the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Harrison, OH
- Parts Used:
- WP40004001
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
noise while spinning
had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bel Air, MD
- Parts Used:
- WPW10121334
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Clanging of dryer when rolling
Followed video on PartsSelect website, they made it real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Olmsted Township, OH
- Parts Used:
- 34847
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The knob....she broke.
I pulled off the old metal sheath with a pair needle nose pliers....grueling....then gently slid on the new knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Adrian, MI
- Parts Used:
- 40002101W
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
We misplaced the fabric softener dispenser.
We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from Temple, TX
- Parts Used:
- 34847
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob was missing
Placed new knob on the post still present on the machine. Very easy. part fit perfectly and works properly with machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Cambridge, MA
- Parts Used:
- 34847
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob on an old washing machine
within about 5 minutes I was able to search on the make of the washing machine and then quickly find the broken knob.
this in spite of not knowing the model number for a 25 year old machine. it couldn't have beeb easier than that.
this in spite of not knowing the model number for a 25 year old machine. it couldn't have beeb easier than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Erial, NJ
- Parts Used:
- WP27001095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washer Wouldn't Turn On
Found out that these switches go from time to time and are usually the culprit when the washer won't operate. Opened the cabinet facing. Warning: there are plenty of YouTube videos on opening Maytag washers. None helped me with this model. I ended up finding the screws to open near the floor on front. Once it's opened, just replace the faulty switch, reconnect and you're in business. Getting the washer opened was about the hardest part of this repair. Total cost: Less than $30.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Gary, SD
- Parts Used:
- WP40053901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
water leaking when washing
I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot
Was this instruction helpful to you?
Thank you for voting!