LNC6762A71 Admiral Washer - Instructions

Brought unit out to garage so I would have room to work on it. Popped the top off, removed two screws to remove the front panel, removed back panel also, since there was no way I was going to the trouble of dis-assembly to get to the snubber without changing those 6 springs also - and you HAVE to remove the back cover to access all 6 springs.Removed belt and level and drain hoses- tub came right out. Loosened those 6 screws without removing them and pulled old snubber out- very straight-forward. Spent 10 minutes just comparing the old and new snubbers- I saw that there's a "ridge" around the inside of the new part that is gone on the old snubber. Sprinkled some corn starch at base of unit where the new snubber will fit (Great Idea someone had!) After everything was re-assmbled, I noticed the tub was now nice and tight when I grabbed it to move it. Before, it took no effort AT ALL to move it all around. Did a test load with some laundry the wife had stacked on the drier. Imagine my disappointment when I heard loud knocking inside when it started to agitate, but not while it spun!
Got all my tools back out and took the wet laundry out to take it all apart again- found the wife's heavy glass vase had been hidden in one of the towels. Re-tested- everything works GREAT!So far I've changed the drum seal (hardest) and the waterpump (easiest)- thi springs and snubber was alsmost as easy as the pump.
Above average shipping from Parts Select also- very helpful and efficient people on the phones.

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Disconnected the power plug. Turned off the hot & cold hose water supply. Put down old bath towel. Disconneced hoses from machine inlet valve. Opened entire top for access to electrical connections & fill hose. Replaced inlet valve, new wire connectors. Replaced the hot & cold water hoses.

This was my first washing machine repair.

After taking the motor off (it looked loose to me!) and stripping out the bolts on it, then finding that the bolts holding the motor were permanently affixed to the motor (and they were an odd size not available at the hardware store), I drilled the bolts out and put in new ones (on the motor) and re-affixed the same. I still had a problem. I then went online and found that most people had problems with the water pump. I looked at the pulley on the water pump and found that the inner shims had slipped out on a permanent part (and could not be put back in with the basic tools I had on hand). I ordered the pump online, and replaced the same. Took about 30 minutes after I found the real problem and got the parts in. My pump had a permanent metal disc on the bottom which did not come with the new pump, but the new pump fit without it. Machine works fine now.

First I raised the top and took out the two screws that held the front on. Then I removed the back panel which were held by 4 screws. Then I turned the machine on it side and removed the belt. I then pulled the hose off from the tub to the water pump and the small hose on the back of the tub. I then removed the 6 springs that held the tube to the base and then I picked the tub up and turned it over on the floor. Then I backed off on the screws that held the snubber in place. I pulled the old snubber out, retighten the screws that held the snubber tight. Then I reversed my steps.

I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the pulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.

My husband did the repair quickly and problem solved. The only difficulty was that the water valve was in a tight spot. Overall, if you are mechanically inclined and have the right tools this is do it yourself project.

removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..

Removed bolt that held old agitator in, removed it and replaced with new agitator.

removed old valve bought new one put it in saved money

I removed the old pump put the new one in its place. In twenty minutes i was ready to was clothes. It was so quite i thought something was wrong. I received the part in three days the timing was great.

took back off washer with nutdriver, pulled wires off by hand, ( was unplugged ). pliars used to remove hose, regular clamp put back on. reinstalled back plugged in, tested water,,,, done

I followed the instructions in the video on the parts select web site. It was very easy, and went exactly as shown on the video. The part was ~$80. I am sure a repair person would have charged me ~$200 for the repair.

The PartSelect video was excellent and very helpful. This replacement took extra time because the washer was located in a tight space and moving/lack of access to the rear of the washer created several issues. Tips based on my experience:
1) I used a MasterLock ratchet tie-down to secure the lid when raising the hinged top of the washer (I wasn't able to lean and support this against a wall as demonstrated in the install video).
2) The fill hose that connects to the water valve was difficult to remove and I needed two large-jaw adjustable pliers to do this. A small amount of Dawn dishwasher detergent applied to the inside of the hose made re-assembly quick and easy. 3) A set-screw holds the valve in place. Easy to remove but because I couldn't get in back of the washer, I had to measure from the bottom of the valve to line-up the screw with the hole in the valve assembly to mount the new unit (this wouldn't be a problem if you could see where the screw goes but I couldn't get in back of the washer for this simple final step). Very pleased with finished result - just needed some extra time and additional tools.

Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.