AAV3000AWW Admiral Washer - Instructions

I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot

I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!

Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

Removed front panel also right side panel to get to the springs. Used vise grips to extend springs and used coins to keep springs open for replacing.

Using nutdriver or screwdriver, remove metal panel from lower left side of back of washer to expose the pump. This is where the drain hose attaches to the washer. Use pliers to move the clamp off of the drain hose, then ease the hose off of the pump by wiggling it back and forth while pulling gently. Be careful to keep drain hose opening pointed upward until you can point it to a bucket, as there's likely to be quite a bit of water in it. Detach drain hose on other end as well (wiggling / pulling works well here; no clamp is used, so no pliers are required). Install new hose by reversing above steps.

I watched the installation video. It was very helpful to see it done before doing the repair. I followed the video to take the old springs out and installed the new ones. Remember to check the snubbed ring and replace it too. The new springs and sunnier ring solved the banging and moving during the spin cycle. Now the washer is like new and the repair was less then $100. Thanks parts select, the help was greatly appreciated.

Removed the old hoses and screwed on the new hoses.

disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather

I used a needle nose pliers to release the turning mechanism from the piece left broken on the timer. Once removed, I simply clicked on the replacemnet part. It was super simple. I love that I can do most things myself with the parts, and not have to pay the expense of hiring a repairman.

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that everything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself

On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.

Hving read some of the tips in regards to this repair I set out with equal parts of confidence & apprehension. The advice of shifting the tub toward the hinge to be removed is in itself the key to the whole procedure. After having done so & wedging a dust pan handle between the tub & frame to first one side & then the other, I removed the entire lid with the hinge & hinge pin assys. attached as ther is not sufficient clearance to slide a servicable hinge pin from a hinge when only one hinge has beeen removed. With the lid completely removed access to the hinge pin(s) is straight forward. I suggest screwing & unscrewing the fastening screw into a new hinge assy before mounting the hinge onto the machine & also using an offset philips screwdriver or ,as I did, a 1/4" drv. ratchet with a #2 philips apex bit which allows for a better feel & more control over the upside down blind operation of removing & replacing the fastening screw into the hinge assy. Hope this helps. Tom

First, I unplugged the washer.

then, I used a small prybar to pop open the front top of the waher. It's hinged at the back top edge. I drew a rough sketch of the four color coded connecting wires so I could disconnect the old water inlet valve and replace it the same way with the new one.
( just in case I lost track of which wire went where.)

I cut off the water supply for both the hot and cold water, (you can also cut off the water main,) then diconnected the supply hoses--noting where the hot water was connected, and where the cold water connected. Maytag had cut out a "C" and
a "H" our of the back wall of the washer,
to assist with hose installation.

I unscrewed the two hex nuts holding the old inlet valve to the back wall of the washer. ( from the outside back of the machine.) and pulled the old inlet valve up to the top of the machine. I didn't remove the basket that holds the laundry, so it was a kind of tight workspace.

Once you reconnect the wires to the new water inlet valve, attach the inlet valve to the washer wall, and reconnect the hoses, it's done. It's pretty simple.

unscrewed screw holding old actuater in and replaced it whith the new part.