ATW4475VQ1 Admiral Washer - Instructions

Watched the video on your site for that part

Before I even watch any partselect videos to do the repair, which I should of from the very beginning, ah, ja, ja, I had already disassembled the back panel "my way" to the washer and trouble shooting the washer with my wife's help. While she tilted the washer backwards, I looked under and we found that the noise was coming from in between top of the motor where the direct drive motor coupling is located and the clutch assembly came together which I learned along with names and functions after watching the partselect installation video. Nice! Once I received the part it took me like 45 minutes to put all back together. Took loose two screws to clips holding the motor, pulled motor of mounting bracket finding the broken piece, replaced it, recouped reinstalling motor onto the motor bracket, clip, clip the two little screws and walla, got the wife her washer back, at bed time rewards, peace of mind the rest was history... Thanks PartSelect for awesome videos and great customer service!

I watch the you tube, and try to fix it by myself,to save money, and moving trouble.this is my first time fix a big machine like this,I was a little scare, but after I saw the youtube about how to fix the washmachine,I start to give a try.it take little bit more time for me to figure out ,but I finally made it. now I can wash my cloth now, and perhaps fix washmachine for my exrat income.( message sharing from an asian 58 yrs old lady, sorry for unable to show step by step due to English not very good)

Followed the video and instructions included with part. At first we did not think the repair was successful, but after several small loads were run, squealing stopped. The washer is 16 years old and so far is running like new. We certainly appreciated the great customer service. The part was delivered in less than 24 hours.

Teeth inside the plastic gear ring had worn down after almost constant use. FYI, this is a "Commercial" branded washer and we have used it almost daily since purchase. It doesn't have the bells and whistles (or the electronic boards) the new ones have, but it washes clothes and does it well! I ordered the complete agitator kit, reasoning it would be faster to replace the entire unit - I was right. The single bolt is 7/16" and required a socket wrench with a 10" extension bar. The hardest part was getting the tools together, and this took the longest. Actual repair only consumed about 10" - remove the bolt, put the new assembly on and replace the bolt. The printed instructions were not completely clear as to whether the thrust washer went above the slip clutch or below it, and I could not get the halves of the old agitator apart to verify, so I went with putting it below the clutch. I am reasoning that the upper assembly should rest on this plastic washer to reduce wear on the separate halves of the assembly.

very easy, pop up the top, unscrew 2 screws, unplug switch , plug in new switch replace 2 screws ,put top down,finished

Unplugged the washer and unscrewed hoses. Unscrewed the 2 screws on the back of the control panel and folding it up. Took off the 2 metal ties to get the cabinet off. Once off, I unscrewed the ground from the old Lid Switch and popped out. Put the new Lid Switch in, screwed the ground back in, replaced cabinet, clamps, put the control panel back in place and screwed the 2 screws on back of the control panel back in. Screwed the hoses back on, plugged the washer back in, everything works great again.

Watched the videos that were very helpful and repaired it my self with no problems its fixed and running like new i took a little extra time to clean all of the washer since i had it apart any ways so the time to fix it was probably was a little shorter i would like to thank part select for all there help and videos it made this job so much easier.

There are youtube vids on how to get the thing open. I just wish I'd known the following: 1.remove agitator BEFORE opening the unit up and leaning it back (much easier to work inside the tube with it upright). 2. be aware that a free-floating part known as the skate plate can dislodge while the unit is on it's side/back. It is a generally triangular piece of flat-ish metal between the base of the tub and the top of the drive-train chassis. If it doesn't line up properly after you replace the parts you're going to get a noisy, clanking spin cycle the next time you run the thing (as I discovered).

I pulled out the old cap with my hands and jammed the new thingy into place. The lady of house did the repair. Easy

I did repair myself with your instructions. it was very easy to do for my age. 84.

watched the video on line showed how to do it took about 45 min no problem

electric unplugged, removed water lines. two screws on back of control housing removed, tilted housing back, removed two clips on top of washer housing, removed body. tilted washer backward, removed brackets on water pump and electric motor, pulled motor off and removed broken parts on shaft, replaced with new parts. Lining up motor shaft to washer was a bit tricky but time and patience got it togather. replaced brackets on motor and water pump. put washer upright and put body back on the body has to be set on guides correctly or will not set right. replace clips andtilt top down and screw it. hook up water lines, and electric.