Models > 4GATW4900YW2 > Instructions

4GATW4900YW2 Admiral Washer - Instructions

Jump to:

All Instructions for the 4GATW4900YW2
91 - 105 of 413
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jeff from Michigan City, IN
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
The washer quit agitating
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the repair man.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
jose from lake forest, CA
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
agitator wasn't moving
first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
jason from Barnesville, OH
Parts Used:
80040
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set
washer would not agitate
removed the agitator and melted the retaining clips to loosen the retainer cover for the cogs. went simple after that.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Walter from Brandon, MS
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Agitator wasn't turning
After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agitator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Zina from Hot Springs Villlage, AR
Parts Used:
80040
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
upper part of agitator did not turn because of worn out teeth on the agitator cogs.
The repair went smoothy except for removing the screw that holds the upper agitator part from the bottom agitator. Once that was removed all went smoothly. Considering my washer is 17years old, I guess I should be happy that was my only problem. I followed the directions of the repairman in the video that was provided by the web site. Most of my parts matched his parts :). My husband was very proud that I repaired the washer and was able to diagnose the problem. Thanks for helping me save some $$$$. I'm pleased and am very happy to have solved the problem on my own. My husband teases me about hanging a shingle. Thanks, Zina
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from WHITE BEAR LK, MN
Parts Used:
80040
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Wrench set
Agitator was skipping and seemed lose.
Removed agitator according to instructions, although upper and lower agitator did not want to separate. I used a steel rod and hammer to separate them by hitting lower agitator where bolt goes through. After removing and replacing old cogs, cog holder had to be tipped upside down to insert in agitator. I used a small dap of toothpaste to hold retainer in place while I inserted it in agitator. Works great now.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from JOELTON, TN
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Taking the adjetator apart.
I went on line to find out how take the adjetator apart. You just stand on the adjetator and pull the top off. Very simple. Once that wss apart I cleaned the dog area of dirt and old pieces. Install new dogs and put it back together. I was trying to make much harder than it was. Piece of cake.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janet from LINCOLNVILLE, KS
Parts Used:
80040
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set, Wrench (Adjustable)
I noticed when putting clothes in the washer and more than half full the top agitator slowed down.
We ordered the dog Agit clutch and within a few minutes I had a new washer. It started agitating a lot faster.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tony from SUMNER, GA
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
upper agitator wouldn't rotate properly/intermittently
Removed the four worn agitator directional cogs and replaced them with new ones
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lorraine from FORT PIERCE, FL
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Top part of agitator did not work. It would only turn sometimes.
I followed a repair video on YouTube It is easier to disassemble the agitator and replace to cogs The hard part was placing the top part of the agitator back onto the bottom parts, after I replaced the cogs. i use a flashlight to help see where the two separate pieces of the agitator need to be to connect the back together properly ( top agitator & bottom agitator). Once this sep is completed you have to place the whole agitator and line it up on the agitator rod. Line up the groves as much as possible. Turn the agitator slowly until it slides into place. Then use your socket wrench to tighten the screw. The screw is the last step to attach the agitator back onto the washing machine. Then replace the cap, to keep water from going down into the washing machine. Then replace the fabric softener dispenser. Now you have a great washing machine. I am a women and did this repair by myself.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
WALTER R. from BEDFORD, TX
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
COGS WERE WORN OUT
THE INSTRUCTIONS ARE ON THE SAME SITE AS YOUR PART WHITCH MADE IT SIMPLE
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kitty from Erie, PA
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Agitator wouldn't turn when washing clothes.
Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're in). Replaced cogs in the same direction they came out. Very simple!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sheila from Greensboro, NC
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set
would not agitate
Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Diane from Corvallis, OR
Parts Used:
WPW10072840
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The cap thingy seal broke and splattered fabric softener.
I pulled out the old cap with my hands and jammed the new thingy into place. The lady of house did the repair. Easy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Noel from Chicago, IL
Parts Used:
80040
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
Upper agitator would not rotate
Could be done in place, but it's easier to pull the full agitator assembly out first, and work at a table. Remove the fabric softener dispenser, then the plastic cap below (with rubber o-ring)- both pull out by hand. Reverse the now visible bolt with an extended 7/16" socket and pull the cog housing up and out, gripping with gentle pressure with pliers ( locking plastic tabs make this piece impossible to remove by hand). Once the housing is removed it's easy to separate the two halves with your fingernails and replace the cogs. I was able to reassemble everything and push it back down into the drum in about two minutes. Piece of cake- I highly recommend anyone with a tool box do this himself.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 4GATW4900YW2
91 - 105 of 413