4GATW4900YW1 Admiral Washer - Instructions

There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.

I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .

I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Cogs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .

Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem

Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.

Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.

The repair was very simple. I removed the agitator cap with a small screw driver, removed the retainer screw with a socket set tool. I removed the top agitator, lifted the cam and removed the old worn directional cogs installed the new ones. I reassembled the agitator. All of 10 minutes.... Very easy

Repair was simple and quick. Started by removing softener cup and removed bolt holding part that housed dogs. Removed housing and slipped of hold down clamp and replaced the 4 dogs then reversed procedure all took about 8 mins

Pop the top off the agitator, remove the bolt, pull off the agitator, pull out the part holding the cogs (dog ears),remove and replace cogs, reassemble. Works great now.