LATA100AJE Admiral Washer - Instructions

I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the pulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.

Replacing the pump with the new pump was very easy for me, because of my degree in Mechanical engineering, so I am use to dealing with pumps, engines, gears,etc. However, my wife watched me do the entire job and she is now able to replace this part in the future. The design of the Maytag is very simple to repair, and for that I am very greatful that we can order the parts and do the repairs ourselves withhout having to call a repairman. This was our first problem after 6 years of smooth operations by this washer.

took back off washer with nutdriver, pulled wires off by hand, ( was unplugged ). pliars used to remove hose, regular clamp put back on. reinstalled back plugged in, tested water,,,, done

removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..

Took off the back plate. Looked to see where it was leaking. Squeezed the clamps on top and bottom to remove from hose and pull hose out.

remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three screws back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.

Unplug power cord; turn off hot and cold water supply; remove water hoses from machine; open top of machine by prying lid open; remove two hex screws holding water inlet valve in place; remove hose from top of old water inlet valve; remove 4 wires; connect bottom set of wires (red and white) to new water inlet valve; reinstall water hose to top of new water inlet valve; install new water inlet valve onto machine using same hex screws; connect remiaining red and white wires; install hot and cold water hoses to machine; turn on water supply valves at wall; reconnect wall plug; turn water type selector to cold, pull out timer and watched the water flow full-force for the first time in 2 years! Have wife give you a hug for saving cost of new washing machine!

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

Back of this washer did not remove, so we had to go in through the top--more restricting space. As you remove the old electrical metal contacts (two each of white and red), pay close attention to where they connect properly. Best to mark them so as not to confuse how to place new contacts. Also, we disconnected a white plastic hose on opposite side of top which determines load size and amount of water, so be sure to look for this.

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.

Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pump hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.

I changed the piece easily

The lid switch is on the right side top of the washer under the lid. I took a putty knife and found the clips that hold the top of the washer and pushed them to release it. I then lifted it up to fully see the lid switch. I unplugged the washer from the wall socket and took out the 2 screws that holds the lid switch in. Then unplugged the lid switch from its electrical connection and put the new one in its place. Washer is working great so far.

Followed the great instructions on your video