AAV4200AWA Admiral Washer - Instructions

First I unplugged the machine, then turned the water supply off in order to disconnect the hoses at the back of the machine. Next I pulled the top up and leaned it back so I could access the water valve at the rear of the machine (You might have to use a screw driver to pry the top off the pins which hold it down in front...). I then unscrewed the the valve and disconnected the wiring and, in order, re-connected to the new valve. Now reverse and turn on the water and yes, the new valve fixed the hot water problem. We can now do the "whites".

Washer was making noise especially when spinning. I took the washer apart to clean it, That is what it really needed. Also adjusted the water level to prevent overflows which caused soap and water to get underneath into the drive belt area as well. During inspection noticed a nick in the drive belt, Although this was not really causing immediate problem wanted to repalce it to prevent problems. Ordered the belt; it came in two days with no special postage. To install, just leaned the washer over on its front on a slight incline. Took old belt off and put new on by turning the big pulley. It is spring tensioned, so no tools. This may be the easiest part repacement I ever did. Took longer to write this paragraph than to repalce the belt.

Disconnect electricity....remove front panel by gently prying up lid.... Remove two small screws at corners of front panel. You may need small nutdriver here or very small hands, you can easily swivel tub out of the way....once front panel is off water pump is at the bottom right... It is only connected by two squeeze clamps and 3 nuts... This is obviously where the adjustable wrench and nutdriver come in very handy... Otherwise this job will be a bit longer....be prepared for residual water to pour out...you will need towels or a bucket....replace old with new one by reversing the process...at this point tilt the entire washer on it's backside or at least at a 45 degree angle to access the bottom... Swivel the motor away to slack up the belt...remove belt and replace in reverse order of diassembling.... Should take no more than 15 minutes.... Good luck!!!!!

I removed four screws to remove a plate to get access to the pump. Then I removed 3 screws to remove the pump. I then put the new pump in place and put the 3 screws back in the pump. Then I put the plate back on and put the 4 screws back in. Then I put the belt on and put the washing machine back in place and connected the water lines and drain line and plugged the washing machine back in and then tested the washing machine to make sure it worked. Job completed.

The Repair went well . I had the hose on in about 30 seconds . The best part about this ordeal was the ease of finding the part on your website , and the speed of the delivery . I had my part in about 2 days , put it on and back to the fun part of clothes washing . I would recomend this company to everyone. Thanks, Rick K.

1. Pulled top off (liquid softener dispenser section)
2. Put 2 socket extension and a 13 mm socket together with socket wrench (tool).
3. Insert tool with 13mm socket end into old agitator and unscrew bolt.
4. Remove tool and then remove old agitator.
5. Turn old agitator upside down to remove bolt.
6. Insert new agitator where old agitator was in washer.
7. Insert bolt.
8. Insert tool with 13mm socket end into old agitator and screw in bolt.
9. Pop top back on.

Hardest part was finding extensions because one wouldn't reach.

Problem fix after replace Snubber ring, I also replace suspension spring and driver belt due to the fact I'm already taking it a part

Popped off bleach cap on top then got socket and long extension removed bolt, cleaned a little then replaced new agitater top.Replaced bleach cap and i was done.

I'm not a washing machine technician but I did nurse a new Kenmore machine for 23 years and was ready for a replacement. Craigslist advertised a Maytag I was interested in and I bought it with the seller's assurance that it worked perfectly. It didn't and I went online to try and figure out what might be wrong. Clearly, the tub was traveling beyond it's design limit and I suspected a spring or two might be involved. Somewhere online, I found the illustrated parts diagram and then went looking for additional information. To my extreem delight, I came across a do it yourself repair video that demonstrated the procedure well enough that I was completely confident I could make the repair with little effort. That video was one of several service related appliance videos offered for free throughhttp://www.do-it-yourself-washing-machine-and-dryer-repair-help.com/index.html/ The final consideration was whether I could buy the replacement suspension springs and snubber ring for less than I paid for the washer. I found PartSelect and within minutes, I had the parts ordered. The parts arrived within 4 or 5 days, as promised, well packaged and in perfect shape. This morning, using the video as a final reference and the new parts, I completed the repair with only a minor hitch. Without the special spring tool used in the video, I struggled a bit with getting the new springs attached. That's where my wife came in handy (after all, she was movitated). Having her tilt the drum toward the spring landing made it much easier for me to stretch it into place using an adjustable locking plier. I actually enjoyed the whole procedure.

Removed entire cabinet from base, removed drive belt, removed suspension springs, removed tub and transmission together.
Removed 6 screws from brake housing to access snubber. Didn't have the special tool to compress the spring for reassembly, but used 3 longer screws to pull the brake housing back down...worked fine. Reinstalled transmission / tub and replaced all 6 springs. Reassembled cabinet. Unit spins great now...like new.

Leaned washer forward, removed clamp and old hose, replaced with new hose, reinstalling clamp.

Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

I read some stuff on the internet where folks with the same problem replaced the water inlet valve to repair this same problem. So I did the same. However, after I installed the new water inlet valve, the problem was still there. It was at that point I decided not to guess at the what issue was and instead test the components in the washer. Yes, I am a lazy dumb ass. There are many of us out there. I decided to use a continuity tester to test all components in the hot water fill circuit and determined that the water temperature switch was bad. So I ordered a new switch from Parts Select (they rock - it showed up next day) replaced the water temperature control switch and...walla. fixed!!! Only took about 30 minutes to replace. Lesson learned: Don't be a dumb ass and guess. Test.

Removed front panel also right side panel to get to the springs. Used vise grips to extend springs and used coins to keep springs open for replacing.

Using nutdriver or screwdriver, remove metal panel from lower left side of back of washer to expose the pump. This is where the drain hose attaches to the washer. Use pliers to move the clamp off of the drain hose, then ease the hose off of the pump by wiggling it back and forth while pulling gently. Be careful to keep drain hose opening pointed upward until you can point it to a bucket, as there's likely to be quite a bit of water in it. Detach drain hose on other end as well (wiggling / pulling works well here; no clamp is used, so no pliers are required). Install new hose by reversing above steps.