LNC6766A77 Admiral Washer - Instructions

Open the top of the washing machine by using a putty knife to release the latches at the right and left side. Prop up the top so it doesn't fall while working.
Remove the inlet hoses and put in bucket to catch water.
Remove the two screws that hold the inlet valve in place.
Remove the wires from the inlet valve. (One of the spade connectors one wire broke and I had to replace it.) I used needle nose pliers to pull the spade connectors off.
Remove the outlet hose.
Throw out old valve assembly.
Attach hose to new valve assembly. (My old valve assy outlet was slightly smaller in diameter than the new valve, but I was able to get the outlet hose to stretch enough to fit--couldn't use old spring clamp though, but new valve came with a hose clamp--worked fine.)
Attach wires same way as they cam off old valve.
Position and use the two screws to screw assy back into back of washing machine. (The screws had to tap the holes on the valve, so start out a little hard.)
Reattach the inlet hoses and check for leaks.
I also ran both the hot and cold in a cycle and the reraised the top to check for any leaks internal to the machine.
Pus the top back down to engage its fastening clips.
Job done.
My washing machine is 23 years old.

First I removed the bolt and removed the old agitator and post assembly then I put the new agitator and post assembly in place and tightened the bolt. It was so easy, when I called the manufacturer they wanted to send out a technician, but thanks to Parts Select I fixed the problem without spending alot of money and without the hassle.

One screw off and pulled the part off. Replaced with new and put screw back in. Fabric softener snapped in place.

After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.

Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.

I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!

Opened up washer, found vacuum hose was broken and replaced it. Removed agitator with a couple extensions and a socket wrench. Found agitator part was worn out and replaced it. The best part was how great PartSelect made it so incredibly simple and easy to find the right part. I'm now a customer for life. Kudos PartSelect.

first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

Removed damaged pulley installed new pullley and clutch. The directions made it easy. Aligned pulley as detailed and installed new front feet and tested washer. Took me about 30 minutes to repair. Washer has been working since. Thanks guys for a nice no nonsense package.

The parts list and schematic made it easy to select the correct part that my wife and I believed was the problem. The plastic part was removed easily because it kept on popping off during the wash cycle of anything other than light low loads. The mechanism was useless. With the new piece/part inserted the machine got back to business as it should be. Plastic just wears out to quick. At least we have delayed a machine replacement.

PROBLEM: The washer lid has two hinge pins that are attached to the lid with Phillips screws (one per pin). The plastic pin that inserts into the hinge broke off, allowing the lid to come free. SOLUTION: First, I removed the lid from the washing machine. Second, I used a Phillips-head screwdriver to remove the original hinge pins from the lid. Third, I replaced the hinge pins. Fourth, I used a flat-head screw driver to pry up the washer top to obtain easier access to the hinge screws. Fifth, I removed the original hinges with a Phillips-head screwdriver (one screw per hinge). Sixth, I attached the new hinges to the washer lid. Finally, I attached the hinges (and lid) to the washer top, then lowered the washer top.

First I unplugged the machine, then turned the water supply off in order to disconnect the hoses at the back of the machine. Next I pulled the top up and leaned it back so I could access the water valve at the rear of the machine (You might have to use a screw driver to pry the top off the pins which hold it down in front...). I then unscrewed the the valve and disconnected the wiring and, in order, re-connected to the new valve. Now reverse and turn on the water and yes, the new valve fixed the hot water problem. We can now do the "whites".

The lid hinges are fastened to the top of the washing machine body, near the edge of the lid, with 1 screw each.
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push the inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!

I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.

if you move the agiatater all the way to one side you can acess the star screws from under the hinge then push the agitator to the other side and acess the screw on the other hinge , you dont have to remove the top of the washer, let me say i did not have the serial no and the people at part select were very helpful and pacient when i called and they got me the RIGHT part the firdt time.thanks again for all your help the job came out perfect and saved me a lot of money for a repair man. ASHER