Models
>
ATW4475TQ0
ATW4475TQ0 Admiral Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for ATW4475TQ0
Viewing 8 of 8Manuals & Guides for ATW4475TQ0
Click to downloadKeep searches simple, eg. "belt" or "pump".
$18.89
This is an OEM direct drive motor coupling, which provides a cushioned connection between the transmission and the motor shaft. This is the newer version of this part, made with new metal sleeves for ...
In Stock
Order within the next 10 hrs and your part ships today!
$8.00
This suspension spring is a genuine OEM replacement part for a variety of washers and washer-dryer combos. The primary purpose of the suspension spring is to support the outer tub and keep the tub ste...
In Stock
Order within the next 10 hrs and your part ships today!
$27.55
This is a genuine OEM replacement clutch assembly for your washing machine. A clutch assembly, also known as a clutch or a washer clutch, is responsible for spinning the tub during the spin cycle. If ...
In Stock
Order within the next 10 hrs and your part ships today!
$7.03
This bolt is a genuine OEM replacement part, used to secure the agitator in your washing machine. Overtime the bolt can become worn out due to the vibrations of the washer, and will need to be replace...
In Stock
Order within the next 10 hrs and your part ships today!
$45.93
On the lid on your washing machine there is a pin that engages with the lid switch. This works by telling the machine that the lid is closed which then allows for the washer to start. If your washer i...
In Stock
Order within the next 10 hrs and your part ships today!
$7.03
This tub spring is a genuine OEM replacement part for your washing machine and is sold individually. There are other names that the tub spring goes by, such as the suspension spring, balance spring, o...
In Stock
Order within the next 10 hrs and your part ships today!
$7.62
The thrust spacer is a genuine OEM part that is more commonly known as a retainer ring. The spacer is made of white plastic and measures approximately 2.5 inches in diameter. This part is found in bet...
In Stock
Order within the next 10 hrs and your part ships today!
$36.45
This agitator repair kit comes with a long cam, a thrust spacer and four dogs ears (agitator cogs). This repair kit is used to move the upper agitator and it connects the base of the agitator with th...
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
$5.41
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order within the next 10 hrs and your part ships today!
$5.77
Also known as Main Outer Tub Seal. This part helps to prevent leaking from the bottom of the tub.
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for ATW4475TQ0
Viewing 14 of 14Will not agitate
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from Wayne, NJ
- Parts Used:
- 285753A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum ... Read more p.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum ... Read more p.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from SLC, UT
- Parts Used:
- 285785
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
spin cycle did not engage
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unb
... Read more
olted the 3 gearcase mounting bolts and took the entire gearcase, shaft, motor, etc... together, out from under the washtub. the clutch slides off the gearshaft with a little fidgeting and the new assembly is easily installed where the previous was. put everything back together... then... spin spin! worked perfectly
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Seattle, WA
- Parts Used:
- WP63907, WPW10250667
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer tub slammed into washer body during spin cycle
If you load a washing machine unevenly, it will spin out of balance. But our washer seemed to make noise during the spin cycle regardless of how the load was distributed. I suspected that the suspension or balancing springs were getting tired, and ordered a replacement set.
First I disconnected the washer from the water and pow ... Read more er supply, then I laid it on its back.
The tub rested on the back of the washer, making two of the three suspension springs relax, and they were pretty easy to pull out with pliers. After the first two were out, I had to support the tub with a couple 2x4s to relax the third suspension spring.
Installation was the reverse of removal - install the lower suspension spring, remove the 2x4s, then install the two other suspension springs.
The tub balancing spring was easy to replace, and probably wasn't the cause of the problem.
With $25 in parts and about 15 minutes, my washer spins much more quietly.
First I disconnected the washer from the water and pow ... Read more er supply, then I laid it on its back.
The tub rested on the back of the washer, making two of the three suspension springs relax, and they were pretty easy to pull out with pliers. After the first two were out, I had to support the tub with a couple 2x4s to relax the third suspension spring.
Installation was the reverse of removal - install the lower suspension spring, remove the 2x4s, then install the two other suspension springs.
The tub balancing spring was easy to replace, and probably wasn't the cause of the problem.
With $25 in parts and about 15 minutes, my washer spins much more quietly.
Read less
Was this instruction helpful to you?
Thank you for voting!