AW20M1A Admiral Washer - Instructions

Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.

Tilted machine back, put a paint can under it and did R & R with belts.

Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done

first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!

Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.

removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!

UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel that you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.

Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hole at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.

used putty knife to to raise the top, took out two screws, replaced parts , then closed the top.

Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!

I followed your video instructions. Very good video.

Removed screw, replaced hinge.

I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.

Rolled the old one off and rolled the new one on.

I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hinge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.