AW20L1W Admiral Washer - Instructions

Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconnected the power and water hoses and everything worked fine.

I changed the piece easily

First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.

Hardest part was figuring out how to get to the water valve. Turned out that the way in was from the top. All I had to do is remove two screws at the back of the top panel, and then unclip the front edge of the top panel (use a thin screwdriver to press in on the clips from the front of the machine). From there, it was easy to reach down inside and remove/replace the valve.

It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was stiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00

Disconnect all water supply and unplug washer. Remove 3 screws on back panel of the washer. This will expose the pump unit. Detach belt on the bottom of the washer. Then detach two hoses that connects to the pump unit. Use pliers if necessary to disconnect hoses. Use 5/16 socket with extension to take out three bolts the connect pump to the washer. That's it, now replace old pump unit and with new. Place bolts back in the 3 holes, reattached hoses, cover the back with 3 scres. Connect the belt to the pulley system on the bottom. Connect water supply and plug it in.

Pulled that sucker out from the wall and leaned him back just enough to prop a case a beer under it. Slid up under there with the biggest dust bunny I ever seen. Yanked that old belt off and threw it away. Tried to uncoil the new one and it slapped me in the nose! Got it uncoiled and around the two smaller pulleys pulling the adjustable one in to it's limit and walked the belt around the big drum pulley. By the time my wife put down her coffee and came to see if she can lend me a hand I was done!.

Rolled the old one off and rolled the new one on.

Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new

first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it a test then let the wife do a load of wash it worked like new

after doing some research I found out that a loose or slipping water pump belt could cause the water pump to not pump out the water correctly. Under the washer is the belt. All you do is have someone lift the front of the washer up enough that you can reach under and remove the belt. Then replace the belt back like you took it off.

pulled the machine out, tilted it backward to expose the bottom. pulled off the old belt. got the new belt started on the three pulleys. pulled the belt to spin it , and...............done !!

Piece of cake. Raise up the front of the machine. the belt slips of easy by turning the main drive wheel. put the belt on the two small one and then rotate the big wheel as you slip the belt into the grove. good idea to first clean the wheels of any old belt material that may be worn off. Piece of cake!

Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the

I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.