AAV8000AGW Admiral Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lester from Elk Grove, CA
- Parts Used:
- WP35-2328
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
I had water leaking from the top of the tub.
I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from MADISON HTS, VA
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Pump locked up so washer stopped working
Removed inspection panel on rear of washer. Pump right there. Removed inlet and outlet hoses with pliers on squeeze clamps. Three 3/8" size self tapping screws were removed and old pump came right out. Reversed process with new pump from this site that fit perfectly. New pump was an upgrade factory part that mounted inside washer without a mounting plate as the old one did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Woodbury, MN
- Parts Used:
- WP43-0057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lid switch acuator broke and some cycles would not work
unscrew the screw holding the broken part in the lid to remove the old part and tighten the screw to a firm position to hold the new piece in place. Now working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from moyock, NC
- Parts Used:
- WP21001915
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Hoes had a leak in it
The Repair went well . I had the hose on in about 30 seconds . The best part about this ordeal was the ease of finding the part on your website , and the speed of the delivery . I had my part in about 2 days , put it on and back to the fun part of clothes washing . I would recomend this company to everyone. Thanks, Rick K.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- keith from auburn, AL
- Parts Used:
- 12002773
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
washer got off balance almost every load.
i followed the directions i found online. do not take the screws all the way out! The snubber ring solved the problem. I replaced the springs since i had them. The old ones seemed OK.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Eagar,, AZ
- Parts Used:
- WP35-6780
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Leaking Water Pump
Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SONY from CONCORD, NC
- Parts Used:
- WP35-6780
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The washer was making a fine squeeling noise that created a foul burning odor
Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Eagar, AZ
- Parts Used:
- WP21001872
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Original drain hose (rubber) was kinking, piece of junk. I replaced it with a new corigated drain hose .
Leaned washer forward, removed clamp and old hose, replaced with new hose, reinstalling clamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Gray, TN
- Parts Used:
- 21001878
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
agitator post broken
removed 1 bolt with 1/2" socket, ratchet and extensionand pulled old part off, replaced with new part---less than 5 minutes total time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BLANCHE from OSSINING, NY
- Parts Used:
- WP21001872, WP285655
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Cracked hose AGAIN!
Hired someone. Note: I purchased two (2) hoses and (2) clamps -- this is the third time I am replacing a cracked hose. The manufacturer needs to use better quality and more flexible material for hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from granada hills, CA
- Parts Used:
- WP35-2044
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
washer lid was no longer connected
Pulled up the top of the washer and removed the lid hinge with a star tip screw driver. Realized that I also needed the hinge pins and had to reorder those. They should come as a kit.
Was this instruction helpful to you?
Thank you for voting!
My Washer's lid hinges broke while it was being moved.
I obtained the parts on line and began to install these. I was surprised that the ease of my installation was great. Each part was held by one screw. I used a phillips driver and found the under screws easy to get to by pushing the inside clothes drum to the side. A total of four screws was required for the replacement. This repair was so easy that a normal non-trained person can accomplish it. Thanks Admiral.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel from Manistee, MI
- Parts Used:
- 21001526
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Knob broke off and couldn't see settings
First, I disconnected the power cord then I removed the panel that held the knobs in place. Then I pulled the center holding clip, what holds the knob secure, with the screwdriver and the broken knob slipped right off. Then I put the new knob on the shaft and slid the holding clip on the backside of the panel. Lastly, I put the panel back and screwed it back down and that's all. Works like nothing ever happened.
Was this instruction helpful to you?
Thank you for voting!
lid hinge broken
I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eleanor from PALATKA, FL
- Parts Used:
- 12002213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer was making a squeak during spin cycle & then just stopped spinning
I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!
Was this instruction helpful to you?
Thank you for voting!