AW20K23H Admiral Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jose from Elizabeth, NJ
- Parts Used:
- WP35-6465, WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Made noise during washing and rinse cycle
It was easy to replace the water pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from CHULA VISTA, CA
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
water not draining
changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILL from DIX, IL
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The Pump Went Out & Water Was All Over My Floor..
Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hollee from Rancho Mirage, CA
- Parts Used:
- WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer making loud noise and tub off balance
I followed Gary from Sioux City IA instructions. Very well explained.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milton from bartlett, IL
- Parts Used:
- WP35-6465
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
discharge pulley assembly bearing going out on it.
Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and did a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lon from Morton Grove, IL
- Parts Used:
- WP35-6465
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
Water pump replacement
Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Modesto, CA
- Parts Used:
- WP35-6465, WP21352320
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washing machine began making a screeching noise but only during the spin cycle - when it was emptying the water from the tub. After a few uses the machine just stopped working.
The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I finally decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Wading River, NY
- Parts Used:
- WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set
noisy out of balance during spin cycles
I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Hinsdale, IL
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Pump was making a grinding noise.
I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALISON from MARTINEZ, GA
- Parts Used:
- WP21352320, WP21001915
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water leaking on floor
Removed back access cover and lift top cover looking for leak. Initially thought it may have been the pump housing. I filled some water into the tub and I flexed the hose between the tub and the pump and water sprayed out. It had cracked in about 3 small places (water is present in the hose anytime water is in the tub) Ordered and replaced hose. Also order drive belt and replaced as a preventive maintenance item.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from King of Prussia, PA
- Parts Used:
- 35-3700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Tub cracked while replacing snubber
Remove tub assembly per snubber replacement procedure.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket
Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.
Always test the air bell before installing an outer tub.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket
Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.
Always test the air bell before installing an outer tub.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Atlanta, GA
- Parts Used:
- WP35-6465
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Washer was leaking water.
Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Katy, TX
- Parts Used:
- WP21001915
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leaking water on the floor-Hose had hole in it
Remove the metal plate in back of the washer that 3 screws. I use a vise-grips to remove the two clamps.One on other the tub side and the other the pump side. Pull the old hose off the tub side and the pump side.Use the old clamps to put the new hose on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ponte Vedra Bch, FL
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
machine woulden't spin properly
diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Baltimore, MD
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Made an awful sqealing noise and did not spin the water out all the way
Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.
Was this instruction helpful to you?
Thank you for voting!