AAV4000AWW Admiral Washer - Instructions

I pretty much followed the video,and read some of the other comments on how to do it. I only had one problem, the back panel had an opening of about 14"x14" to access the 2 rear balance springs. I finally laid the machine on it's face,so I didn't have to kneel down.The only problem with that,is the tub falls forward, making the springs farther away from the upper hole to attach/stretch, the springs to remove/install. I cured that problem by cutting a wedge out of a piece of 2x4, and stuck it between the top edge of the tub & upper frame. Worked great,held the tub in position, closer to the springs & locating holes. Taking them off is no problem,installing them, was made easier by using the wedge. The parts were a perfect fit, no more 'walking away from the wall' now! Thanks PartSelect

Removed one bolt, main thing was I had to buy a 10 inch extension for the socket and wrench to reach inside of the agitator, pulled the old one off replaced the new one tighten the bolt and I was done. 10 minutes start to finish.

Removed the screws on the back plate pulled the hose clamps off removed the belt and three screws off the pump went back just as easy and the machine was like new again. If only all repairs was this easy!

Pretty simple repair--popped the fabric softener cup off of the agitator top and took out the bolt that secures it to the assembly. Removed the broken agitator top, replaced with the new one and reinstalled the bolt and softener cup. EZ as pie for only $24 including shipping! Great price!

Fabulous turnaround time from www.partselect.com. I had the problem corrected inside of 4 days using standard shipping. I will definitely do business with them again!

I first had to take the old part out to find out what the part number was. Then I went online and ordered the part. Once the part came in I attached to part and replaced the drive belt. I did not think it could be so easy.

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

I checked the belt 1st. It didn't look like it could be the problem, but it needs replacement anyway. Replacing belt is very easy, this 1 is at the bottom of the washer.

1. Unplug washer.
2. Move it away from the wall.
3. Tilt washer back & support the bottom front with lumber.
4. You can see the belt looped around 3 pulleys. Water pump in the back. The motor is in the right front & is spring loaded.
5. Grab the motor pulley & push it back as far as it will go, & remove the belt from it.
6. Do the reverse to install new belt.

There is a Brake Rotor & Lining Assy on this washer. I looked up the part on this web site, sure enough somebody else had this same problem. Part is on order. If this is not the fix, I will revise this posting later.

unscrewed screw holding old actuater in and replaced it whith the new part.

The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

followed video instructions

Pulled machine out from wall. Tilted back and rolled belt from pulleys. Pulled further out and removed cover plate 3 screws. Disconnected hoses with pliers and removed 3 screws with nut driver took out old pump and placed new pump into position. Replaced screws and hoses replaced cover. Tilted machine and replaced new belt. Put machine back in place. Started machine with no laundry. Checked for leaks Done. Approximately 20 minutes. Working great

I followed the video you have on web site. Very good and easy to follow.

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was done, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.

Took the whole machine apart tipped tub upside down to put on snubber ring. One person had to hold down very very firmly to the metal ring that fits on top of the snubber ring while another person quickly screwed in the screws to hold it down.
The springs required an extra strong person and a few words of frustration to stretch to get them on. My son who is 39 years old did it. My 60 year old husband would not have had the strength to stretch the springs.
So far it works great. My son washed his carheart jumpsuit and coat with not a sound or wiggle. Your trouble shooting site was what made us decide to order what we did because of the percentages of what the problem was beside each part. Thank you for being so prompt in sending our parts.They came so quickly we weren't without a washer but maybe a day or two.