AAV8000AJW Admiral Washer - Instructions

removed 1 bolt with 1/2" socket, ratchet and extensionand pulled old part off, replaced with new part---less than 5 minutes total time

I used a screwdriver to release the front side of the waaher top from the clips and tilted the washer top back. I then released the hose from the water valve and took out the mounting screws at the back. Replaced the valve and hooked everything back up.

Hired someone. Note: I purchased two (2) hoses and (2) clamps -- this is the third time I am replacing a cracked hose. The manufacturer needs to use better quality and more flexible material for hoses.

Pulled up the top of the washer and removed the lid hinge with a star tip screw driver. Realized that I also needed the hinge pins and had to reorder those. They should come as a kit.

Looked under the symptoms .I had replaced the belt 2 weeks ago, so I ordered the drain pump. Pulled washer away from wall, removed water lines, unplugged electric. I removed the rear panel, found the old part right there, disconnected the in/out tubes, removed old pump, installed the new, re-attached hoses, reinstalled the belt over the 3 pulleys, re-installed access panel. Reconnected water and electric after placing washer back in position. Runs like a new machine!

Removed the old hoses and screwed on the new hoses.

For this repair the tub must stay centered in the machine. I used a shim between the tub and front panel. Tilt the front of the washing maching aginst a wall and brace if needed. Remove the belt and pully. To remove the stator, I replaced 3 of the 6 bolts with a 2" long bolt of the same thread (replace every other bolt). This is needed because the spring is under 100# pressure. Remove the 3 original blots and than the 3 2" bolts. Remove each of these three a little at a time. Install the new stator and brake rotor. Use the 2" bolts in the stator to compress the spring. Reinstall the the other 3 bolts, pully, and belt.

First, I disconnected the power cord then I removed the panel that held the knobs in place. Then I pulled the center holding clip, what holds the knob secure, with the screwdriver and the broken knob slipped right off. Then I put the new knob on the shaft and slid the holding clip on the backside of the panel. Lastly, I put the panel back and screwed it back down and that's all. Works like nothing ever happened.

I obtained the parts on line and began to install these. I was surprised that the ease of my installation was great. Each part was held by one screw. I used a phillips driver and found the under screws easy to get to by pushing the inside clothes drum to the side. A total of four screws was required for the replacement. This repair was so easy that a normal non-trained person can accomplish it. Thanks Admiral.

I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot

Using nutdriver or screwdriver, remove metal panel from lower left side of back of washer to expose the pump. This is where the drain hose attaches to the washer. Use pliers to move the clamp off of the drain hose, then ease the hose off of the pump by wiggling it back and forth while pulling gently. Be careful to keep drain hose opening pointed upward until you can point it to a bucket, as there's likely to be quite a bit of water in it. Detach drain hose on other end as well (wiggling / pulling works well here; no clamp is used, so no pliers are required). Install new hose by reversing above steps.

There is a small back panel about 14" square made to open for access to the drain pump. 3 screws for the back panel and 3 screws for the pump - Oh you do have to slip the belt off & back on, underneath the machine.

Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

Studing the numerous notes under the parts listing, help me determine which parts to purchase and replace. These listings also helped me to do the repair with much ease. Once the front and rear panels were removed, I detached the springs which came out very easily. I then pulled out the tub and removed the pulley and loosened the screws holding the snubber which then came out. Put in new snubber tightened screws, replaced pulley & put tub back in place. The springs were a little tougher which led me to believe the old ones were streched. I used a towel to brace tub to one side so as to attach spring on the low side. Used Vice Grip pliers and could not phathom using anything but. Put everything back together and washed a load of towels. The tub was way more stable, but still, towels were little damp. Respun and they dried. Determined that the repairs was all good but told wife not to put so many towels in at once which is probably why the snubber & springs wore out.

I took the washer into the garage, removed access panel from back. Spun drive belt. This located the trouble with the pump. I removed pump with three sheet metal screws and hose clamps. Upon delivery, I notice the two pumps were not identicle. I called Cust Serv. They assured the difference was ok. I installed the new pump with three screw, put the belt and panel and hoses on and ran a test load of my junk clothing. No trouble.