AW26L3HSK Admiral Washer - Instructions

changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks

Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .

Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump

Reverse the process to install a new pump

Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.

The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.

This was is 1st time we used your server but it won’t be the last!

Kudos to the entire staff and please…keep up the good work.

Sincerely,

Lon Thomas

Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and did a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.

I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!

I followed Gary from Sioux City IA instructions. Very well explained.

The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I finally decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]

Remove tub assembly per snubber replacement procedure.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket

Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.

Always test the air bell before installing an outer tub.

Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.

I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.

diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.

Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.

I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groove and started turning the pulley by hand. The belt went right on.

Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!

First I am a woman and was able to do it, and if I can do it anyone should be able to do this. The service call alone was 75.00, and the belt was 23.00 with shipping. First we tilted the washer at a 45 degree angle and I removed the belt, and just rolled the newer one on the track. That was it and I was done. My washer now purrs like a kitten love it. And Part Select sent out my part and I recieved it next day, thank you for wonderful service that kind of service is hard to find. <3