WET4027EW1 Whirlpool Washer Dryer Combo - Instructions

I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.

Unplug electrical cord, disconnect water inlet hoses and drain line at rear panel. Move washer to garage or larger work area if necessary. Disconnect control panel from top of washer cabinet by removing the two screws at the front corners of the control panel. (The control panel can now be flipped up and back when you are ready to remove the cabinet assembly.) Disconnect the rear panel from cabinet assembly by removing attaching screws at bottom of rear panel (and along the vertical edges if any screws are installed there). Either slightly lift the rear panel up off of the two clip brackets that attach it to the rear top edge of the cabinet assembly, or if need be remove the clips from the cabinet slots. With the rear panel loose, slide the control panel assembly slightly towards the rear and up to disengage it from the cabinet slots, then tip it up and back, away from the cabinet. The cabinet assembly (with top attached) can now be tipped forward and away from washer to expose the internal workings. (It may be necessary to support the rear panel and/or control panel.) The water pump is attached to the front of the motor by two spring clips. Disconnect the two water lines from the pump, then remove the two spring clips. Pull the pump forward off of the shaft extending out of the motor. Install the new pump, then assemble the washer in reverse order. (I was unsure where the leak originated on my washer so I completely removed the rear panel which entailed disconnecting from it the electrical cord fitting, drain and input water fixtures and various other brackets. Pump replacement can be accomplished without completely removing the back panel.)

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

Took back cover off
Disconnected part
Put new one in
Reconnected wires
Put back cover on

To verify that this was the needed part, I used a digital multimeter to confirm there was no continuity.

My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 business days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!

Replacing the part was easy: unscrew the old one from the front of the dryer after opening door, disconnect and replace with new one. Getting to it was a bit more difficult: Remove 6 screws from the back, 4 that hold the back of the top down and 2 that hold the control panel in place. You had to remove the control panel to free up the wiring bundle (held in place by a tie wrap inside the control panel housing) so you could move the top forwards enough. Then remove the top of the dryer by lifting the back up slightly and moving it forward to disconnect from attachments in the front and move aside to gain access to the switch.

My Whirlpool dryer had no heat. I removed the back panel and within minutes diagnosed the problem to a blown thermal cut-off fuse. I ordered a thermal cut-off kit on a Sunday night and had the parts at 7:30am Wednesday morning. Total time for diagnosing and repair was no more than 15 minutes. PartSelect saved me a ton of money and aggravation!!! AWESOME!!!!

Gary

simple and easy . Just tipped the machine back, pump was right there in the front.
Hardest part was getting the old pump off the shaft. I used a small block of wood & a large screwdrive to pry it loose (gently).

After it came off I filed off some corroded spots on the shaft before slidding on the new one. then its slid on easy,
Snapped on the clips , clamped on the hoses, Done, Momma's Happy, I'am Happy

Ordering was easy, Shipping was fast.
I will use you again.

First I did a search on dryer repair. Found a website that described easy things to check with an ohm-meter. I then performed the continuity checks on the items and found the high-limit one was open, in other words, no good. It works similar to a fuse. All this was done after removing the back panel, just a few screws. The reason it exceeded the high limit, possibly because I never opened the back up and cleaned it. Found out it should be done every couple years. My vent line had a hole in it and was letting lint get drawn into the heating element, could have been a fire.

Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519

Took of the back cover, and removed the vent connecting the blower motor to the drum. It was completly full of lint, so cleaned it out completly, and tried the dryer again. The heater element was still cutting off early, and the clothes were not getting very warm, but better than before. Decided to change the thermal cut-off switches. Ordered the parts on Sun, they came in on Tuesday. Dryer was up and running Tuesday night. Just 2 screws per switch, took less than 1/2 hour. The dryer now runs like brand new, and my wife was ready to fork over $800 for a new one!

I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off without unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.

The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.

It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.