WETLV27FW0 Whirlpool Washer Dryer Combo - Instructions

My husband actually did the repairs all I know is he removed the lid, removed the old switch and put in the new one. My washer works now and thats all I care about. I thank you for having the part and at a reasonable cost we were able to repair our washer considering it is twin stackable and is over 10 years old.
Thanks again!!!!

First off unplug the machine then turned off H/C water supply and removed hoses, laid the machine on its side, removed 3 motor supp. bolts, loosened drum pulled out shaft and clutch assembly was right there. Also replaced coupling while it was apart. And to think, a svce company wanted 179.00 just to walk in my door and diagnose the pblm. Then, parts and labor were extra. Thanks for the help/advice, piece of cake!!!!!!!

Laid washer on front side and removed top spring, then lifted the tub assembly to replace the right side spring, the one behind the motor was the hardest, I lifted the tub then removed the spring bracket at the tub with pliers and a socket. The top seal all I had to do was take the 4 screws that hold the top on (it takes a long extension) then sit it bak up and I lifted the top up to give me enough room to unsnap the top piece of the tub, cleaned it up put seal in. The parts fit perfitlt and real fast shipping, I bookmarked the site and will buy from again. JIM

1. Unplug the machine.
2. Turn the water off.
3. Disconnect the supply and discharge hoses.
4. Open the cover and remove the cap/cover of the agitator. Use socket wrench to remove the bolt securing the agitator. Pull up on the agitator and remove it.
5. Lay washing machine down on it's front. Remove the inlet and outlet drain hoses from the discharge pump.
6. Remove the 2 "faston" connectors from the motor start capacitor (looks like a D cell flashlight battery). Rock the connectors back and forth and pull gently until they come off. Polarity doesn't matter but to be safe make note of the positions.
7. Press the release clip on the motor connector and pull to disconnect it. Move the wiring harness out of harms way.
8. Remove the 3 bolt securing the motor and transmission assembly to the bottom of the tub. Pull the drive assembly out of the machine and place it on a suitable work surface.
9. Examine the tub brake assembly (still on the bottom of the tub), the clutch assembly (on the motor/transmission assembly you just removed and everything else for wear or damage. Now if you decide to proceed with repair continue with the following steps. If not you're done.
10. Remove the inverted cup washer from the agitator shaft of the assembly. Remove the "U" clip from the shaft and remove the clutch mechanism from the drive assembly. Make a sketch of the position of each of the removed components to aid in reassembly.
11. Now you can see the gear case cover and it's seal. If it is leaking (as mine was) you will need to replace it.
12. With the assembly level remove the bolts around the cover and remove the cover. Place the cover on a flat surface and with a screwdriver or punch drive the old seal out of the cover from the outside in.
13. Clean the seal area and check for damage. Clean the cover and transmission housing surfaces of old gasket material. There is a factory sealant available for reassembly but I chose an automotive RTF @ $4 vs $24 and it worked OK.
14. Installing the seal requires some tools and experience to done successfully. The right size sockets or piece of pipe, coupled with an arbor press or vise will get the seal in. The cover is delicate so if in doubt find a machine shop.
15. Support the outside of the cover on a hard surface and with a socket or short pipe length, PRESS (don't hammer) the new seal into the gear case cover.
16. Make sure there is lubricant in the gear case. Not overflowing but maybe 1/2 full when view with cover off on a level surface.
17. Apply some RTV sealant to trhe cover and install it. Tighten bolts evenly. Light torque (1-2 ft-lb).
18. Reassemble washing machine and test for leaks and proper operation.

turned the washer on it's back and shoved the tub to the side to release pressure on a spring ,pulled it loose and installed new one. this worked for the back two then turned washer on it;s face and repeted the process on the front spring.
Washer works great now.

Everything seems to work on the electric/gas dryer, but would not generate any heat. Did some research and ordered the thermal fuse & thermostat based on that. Replacement was simple and went well, however it did not fix the issue. Should have checked the continuity first as I found the "replaced parts" to be good. Have checked all other possible symptoms except the heating element, which requires addition labor. Overall, partselect portion was as advertised. All parts arrived quickly and were priced fair.

The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about two days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.

I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.

If you were to do the Belt Replacement only, here is the quick synopsis:
1. Unplug dryer;
2a. Open lint door on top of dryer and remove the two phillips head screws that hold the lint bay to the metal dryer top;
2b. Next remove the two brakets holding the metal top to the dryer back (one screw on each bracket);
3. Use a flat-blade screw driver to pry off the top of the dryer (leaving the timer and start button area attached);
4. Lift off top and push back to expose just enough area so you can get to the two screws holding the dryer sides to the dryer front;
5. Unplug door switch;
6. Unscrew screws from #4;
7. With door open, lift dryer front (only about an inch) and then pry bottom of dryer front from dryer sides. The bottom of the dryer front is not screwed, just siting on Front Panel Clips;
8. Once the front is off the dryer, simply remove the belt and install the new one. Please note that while you are in here, you may want to inspect the rear drum seal and replace if it is worn to the point where metal is rubbing on metal. This is also a good time to clean out dust from inside this cavity to help extend the life of the bearings on the rollers and prevent dust from accumulating and gunking up the motor, etc.
9. Re-assemble tin the opposite order.
If you have any mechanical sense at all and you don't know anything about dryers, you will be surprised at the simplicity of the dryer.

After disconnecting the electrical supply, first remove the two screws at either end of the control panel and fold it back away from the washer top. Then, unplug the electrical lid switch connection. Now, remove the two clips at either end on top to disconnect the housing from the washer back and chassis. The motor is sandwiched between the water pump in the front and transmission at the rear. The Direct Drive Coupling connects the rear motor shaft to the transmisson. After you have taken the outter portion of the washer off, remove the two snap clips that hold the water pump in place and slide the pump off the front shaft. Best to also disconnect the upper hose connection so the pump can be moved out of the way. Caution though, remaining water in tub will drain out. Now remove the two screws that hold the clips in place which secure the motor to the transmission. Careful, as the old Direct Drive Coupling is probably destroyed, the clips are the only thing holding the motor in place and the motor needs to be supported so it won't drop to floor when the clips are removed. Be careful not to lose the four rubber grommets which sit between the motor and transmission bracket. After motor is on floor remove the old plastic slip-on direct drive coupling discs from both the motor and transmission shafts. The new replacement discs have steel centers which do not slide onto the shafts as easily as the old plastic ones did. I had to tap the center steel portion onto the shafts using a hammer and a deep wall socket the same width as the steel portion of the disc. Be careful! I'm sure that tapping the plastic portion of the disc to properly seat it on the shaft will break it away from the steel portion. In my case, It took me several attempts to completely seat the new discs. I had to do quite a bit of tapping to get the discs seated far enough onto the shafts so that the motor slipped easily against the transmission bracket grommets and the retainer clips snapped back into place easily. Reassembly is simply reversing the steps you took when taking the unit apart. Before putting the outter housing back in place, I checked to make sure everything was running smoothly by jumping out the electrical snap-in connection for the lid switch and running the machine in the spin cycle. Remember, if you don't jump out the lid switch and just try to test the unit in the aggitate cycle, the machine has to first fill with water.

checked to see what the problem might be according to your website, ordered the recommended parts, received parts within 3 business days, watched video on website with instructions, replaced parts and surprise, dryer works as if nothing ever happened. thank you for the straightforward, no nonsense information and video provided in your website and the promt efficient service

once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!

Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.

I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.