LT4900XMW2 Whirlpool Washer Dryer Combo - Instructions

Removed old assemblies manually and replaced with new. Very easy and the parts fit perfectly!

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

We watched a video on YouTube; it was very easy . We had to use the mounting bracket.

I followed the video. So easy..

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

Removed the old hoses and screwed on the new hoses.

Removed screws from top control panel. Tilted panel back. Unsnapped two retaining clips and pulled entire washer cover forward. Turned off water and uplugged washer. Disconnected hot and cold water supply. Disconnected supply tube from water inlet valve. Disconnected electrical hook-ups to water inlet valve. Removed water inletvalve. Installed new valve being careful to use new mounting plate supplied and making sure screw holes line up correctly. Re-connected all disconnects and it works like new!

Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.

I followed the provided video for changing the centerpost gasket.

I successfully completed the repair. I will say that I had challenges at almost every step. Getting the inner basket off the centerpost was difficult, as was rocking the outer tub upward from the base.

If a man is somewhat handy, this is a doable repair. Be patient and take your time. The video is very helpful and I don't think I could've done the repair without it. It's a pleasure to watch an expert like Steve.

It's gratifying to successfully repair a major appliance such as a washing machine and I look forward to many more years of reliable service from this well-built appliance.

my hany man did it....

Replacement fit perfectly.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Excellent and super easy. Owned the box and snapped the new one in. Ready for laundry again in a matter of minutes.

I would not ever consider this a repair. The dryer filter cracked because of my wife put it in loosely. The new one just fit right in.
What was so good about the entire process was how quickly I recieved the part. A matter of two days.

My wife did the repair