LTE5243DT3 Whirlpool Washer Dryer Combo - Instructions

After unplugging and removing the back cover from the dryer, locate the push button switch. Slide putty knife around outer cover to unhook catch. Replace with new push button switch. My dryer is still not working, but this was a simple replacement.

took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.

Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.

Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.

First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!

Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.

PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.

Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs and moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.

we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!

I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.

Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.

The reason it took as long as it did was because the job is not in line as the work I normally do.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.

First unplug dryer, then remove 4 screws along the back of the top and remove top and set aside. Next pull outward on the front until the front clears the drum and lift off the front and set to the side, careful not to stretch the wires to the door switch. Remove old belt and slip belt around the drum and line up with marks from old belt. Reach in under the drum under the motor and lift up the tensioner. Insert belt through tensioner and slip over the front of the shaft on the motor and release the tensioner. The belt should now be tight. Reinstall the front and top, plug in and test.

After taking the entire washer apart one time, we learned that we could take the top and front of the machine off only to repair it. I found Part-select online and with the model number locating the part was easy. It arrived within 3 days and with instructions I could easily replace the old part with a few tools. I spent dollars instead of hundreds for a new machine.