MLXG62RBW0 Tappan Washer Dryer Combo - Instructions

Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.

I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.

Taking apart the dryer was easy. Pop the top, take out two screws, separate the front panel from the drum. Removed the old felt seals but much remained. Used a wire wheel on my drill to clean off felt and old glue (most difficult part). Applied new glue,used a band clamp, one hour later I reassembled the dryer; works fine. No more burn marks on clothes!

there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!

disconnected power unlocked both top sides ,lift top back and take top 2 screws out, then unhooked wiring,then remove whole front away from drum.scrap off all the remaining pieces, then glue and wait till tacky, then apply
front lower basket seal and top drum glide seal,replace the front ,hook wires back to proper place , put the two top screw back on!!! happy drying!!!

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing

Remove top cover and front and remove drum and install a new bearing kit and new belt.

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!

replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

As all others have said, without being redundant, I'd view post #1 or #2 for a good detailed set of instructions.

The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I could see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.

Once I figured that part out, it was a piece of cake.

Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)

Removed the door and replace the upper glide and the lower seal. The repair was easy.

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you

Partselect provided me with what to look for with my symptoms and excellent delivery time.

I first looked at your directions then felt I could do the repair. So I ordered the part. The video was extremely helpful and allowed me to follow each step in the process. Last time I paid $270 for the exact repair. This time I costs me under $30. Plus I was able to clean out the entire inside of the dryer. The sitr instructions were very helpful and on target for any level of experience. I fixed my own dryer and saved a ton on it! Thank You, Randy In Colorado