LTSA9AQN Speed Queen Washer Dryer Combo - Instructions

I took the front of the dryer off. The two gas valve coils were right in front. Replaced the two terminal gas valve coil and the secondary coil valve three terminal. Cleaned the inside with shop vac and re-installed the front dryer panel.

The first thing to do is to check to be sure the vent is clear. The easiest way to see if this is the problem is to pull the dryed away from the vent and let it vent into the room. Once you have determined that the vent is not the issue, take the front cover off and see what is going on on the inside. To remove the front cover first remove the 4 screws on the inside of the upper cabinet to take off the control panel, I was able to gain access to the screws under the front of the control panel that hold the front cover in place. A couple of electrical connectors later the cover is removed. The coils are easily accessed from in front of the burner by removing the 2 screws that hold the small silver cover over the coil. Once the cover is removed, the coils slide off a short shaft and you can replace the coil by swapping the apporpriate electrical connector for the coil being replaced. The coils are alligned with a small white pin so you can't get it wrong. Replace the covers and fire away.

This repair is easy and saves you a lot of money. This is a great web site, easy to identify the parts you need and the delivery is very fast. Nice Job!!!

The diagrams listed online gave me a the information needed to trouble-shoot which part could be broken. It only took two tries to see which part was out but was significantly cheaper than a repairman. The expediant delivery on parts made down-time a minimal. Very pleased with results.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

First of all, Parts Select is a great service. By giving us an idea of what parts we needed we were able to buy them without a lot of expense. My son and I did this repair together, and it took us a long time. We found an excellent video for repair on the web, and then lost it and couldn't find it again. We had trouble even getting the dryer opened up. That is where a putty knife comes in handy. Be sure to find out how to open it; it will save you a lot of grief. It is supposed to be easy, but it wasn't. Still,it was great to get it fixed so inexpensively. I'll leave the "how I did it" part up to people who had an easier time, but no regrets that we did it. Parts select sent the parts right away.We ended up only using the coil kit.

tested all limit switches with electrical meter to see if they were bad. All switches tested and ohmed out fine. then looked in and saw a hot serfice ignitor and went right to the problem. I have been a furnace man for some time which would give an advantage over the average do it yourselfer. Once I found the bad part and checked resistance across the element, I instantly went on line and ordered the part.the part came in one day and it was the exact part nothing generic, put the part in and was drying clothes again in only two days. Thankyou so much and I hope to get another 5 yrs of drying clothes out of this appliance. Jim P.

I started by taking the front of my dryer off and cleaned it out. Next i ran the dryer and watched the flame starter circut. The starter circut would work once and then not for a long time but i could see it was tring to light because the iginiter would glow white hot. I then searched online for my model number and found the part select web site. In a few minutes I found a dryer fault description that best fit what my dryer was doing. The part select site should me three parts it might be. I read about what the three parts did on the parts select site. Then by using the process of elimination, with the knowledge I had just learned, I narrowed my suspect parts down to one. The coil for the gas valve must be the problem. So I got my ohm meter and measured the coil resistance and I found that when the coil was room temp it had resistance. But it would get hot after one heat cycle and it would open up therefore causing the gas valve not to open......no heat! I ordered the part and it came in two days!!!! All fixed!

This repair is very simple. (1) remove the lint screen bracket on top - two phillips head screws. (2) Gently pry open the top of the dryer with a large flat head screwdriver. It hinges backward. (3) Remove the top two nuts on the front panel. Lift the panel upward off the lower brackets. The door wiring is still connected, so I just rotated the front panel to the side. The interior is now exposed. (4) Take the drum belt off the tensioner assembly and pull the drum out. (5) Remove the coil retention plate - two phillips screws. (6) Disconnect the old coils, install new coils. I started the dryer up while disassembled to ensure the new coils worked and the burner fired. But a word of caution ... don't run the burner long with the dryer apart, as it could overheat. After all of this, reverse the process. YouTube also has a couple good videos showing all of this visually. I have very average mechanical skills, and this was an easy job. Another word of caution: most of the metal surfaces inside the dryer have nice sharp edges. Invest in a good pair of gloves to avoid mincing your hands up.

At first I thought the sensor in the drum part was bad. It had some residue from something on it and looked a bit beat up. Replaced it for 30$ and had the same problem. Note: I decided to take the console panel off because I though it was necessary to get to everywhere else and I found a folded up "repairman trouble shooting guide" in the console. Don't know if this is a common place to put it but it had all the wiring and problems detailed with this dryer. It had step-by-step assessment procedures for any problem. However, I punched the sequence for the "brains" to give me a problem code and it indicated that I needed a new "user interface," a 285$ part. I must have punched it wrong because I started to read other problem descriptions and I realized, based on others, that the most likely cause was the coils that regulate the gas/heat valve. I used the "problem guide" to measure the resistance of the coils (it gives you the proper range for each) and one was outside of what it should have been so I purchased a new set of coils for $20 plus shipping. It took me 2 tries at installing the coils because the cover plate that seats the coils in place was not aligned properly the first time. This cause them to vibrate and rattle when starting up. The coils were a little different in height so I readjusted the cover bracket and seated the coils properly. No rattle and the dryer worked perfectly.

My father and I were deciding on weather or not to purchase a new stove. The stove had always worked well but one of the front burners would not work and the broiler element was cracked in half. I thought I could fix it and save alot of money and not have to purchase a new one. I entered the model # into the search engine from parts select, alot of discontinued parts came up that were unavailable. I then went to search by product and narrowed the selection to brand,size,metal,and category such as electrical. I was given like models that have these parts in common. I was surprised how many parts were available for my stove. I had originaly bought the unit through Montgomery Ward. Admiral, Maytag, and Whirlpool share many of the same parts. From the photos and descriptions I was able to find the correct parts. I purchased a new burner element and a broiler element. Unplug the stove first. The tools needed were a Phillips screwdriver and believe it or not that is it. Two screws held the top of the stove to the main cabinet. After removing these screws from the bottom of the stove top. Note all you have to do to find them is open the door and look under the stove top. The whole stove top swings up and back letting you access the burner elements. Three screws hold the element to the bottom of the stove top. Remove these and note the four electrical wires attached to the burner element. Make sure you mark or notate the location of each wire. Attach the new burner and hook up the wires to it. I put the stove top back down and plugged in the range. The new burner element worked but the switch didn't shut it off. I unplugged the stove and removed the the back plate at the top of the stove. The plate is held on by eight Phillips screws. You only need to take the top back plate off. Don't take the bottom one off. After removing the the plate I could access the switches for each heating element. The left front switch had scorch marks on it, so I knew that it was burned out. Another way is to test the switch with a continuity tester and see if there are any open contacts on the switch. I ordered the switch. It was delivered in two days. I removed the old switch by pulling the knob off the switch and removed one Phillips head screw holding the switch in place. I removed each wire and attached them just as they were attached to the old switch. I ratcheted the switch and plugged the stove in to the outlet and the new burner and switch worked great. I removed the old broiler by taking two Phillips screws out and carefully pulled the old broiler element out. I only pulled the broiler element about four inches from the back of the stove. There are two wires that slide off the broiler element. Remove them but don't let them get pushed back into the holes that they are located in or you will have to take the entire back of the stove off and push them back through there openings. I unfortunately did this and this added time to the repair job. There are two Phillips screws that hold the broiler element holding bar they are located inside the roof of the stove. Remove these screws and slide the old broiler element out. Slide this holder on the new broiler. The holder slides back and fourth on the broiler element so you can position it in the right spot. First attach the electrical connections by sliding on the two wires to the broiler. Push the broiler ends back into there holes and attach them with the two Phillips screws. Next slide the broiler holder on to the broiler element and then position the broiler on the roof of the oven. Attach with the Phillips screws. After doing this I plugged the stove in and turned on the broiler and it works great. There were alot of screws that held the back top plate to the stove and other screws that attached the switch, burner element and broiler element in place, so it would be a good idea to note were these screws are placed. Then there will not be a problem matching

Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.

Downloaded a schematic of the dryer controls. Watched a UTUBE video of how to remove the front panel of a Maytag Performa dryer. It was pretty easy. Consulted your website and found out that bad coils are typical of the symptoms 46% of the time. I have bought parts from you before and happy with results.

easy as pie !

This turned out to be easier than I thought. I opened the access door on the front of the dryer after unplugging the dryer and turning off the gas. I reached in just inside the door with a short-handled phillips head screwdriver and removed the two screws holding the two coils in place. The screws were pretty tight and a bit difficult to get loose but after serveral attempts they finally broke loose. Once I removed the plate that covered the two coils they just slipped right off, much easier than I thought. I removed the electrical connections then attached the wires to the new coils and slipped them back on their respective pins. I reattached the "cover", then plugged the dryer back in and turned the gas on and started it up. The flame fired right up, much stronger than before I replaced the coils and of course the flame stayed on. Problem solved. Repair was really pretty simple with the diagnosis being the biggest problem.

The gas would light briefly then go out so the clothes were never heated. I googled the problem and found your website and read a few blogs describing the problem, ordered the coils, popped them in and presto it worked.