MLE20PDBZW1 Maytag Washer Dryer Combo - Instructions

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Since i knew the filter was cleared of obstructions I knew the code issue was something more serious. After consulting with local repair reps I decided that the drain pump was beginning to slow down causing the faults. First, I took the lower front panel off the front of the washing machine so that I could drain the water out of the plumbing. After draining the water out of the pump into a pan, I went ahead and then lifted the front of the washer (and dryer on top of it) and tilted it back far enough so that my wife could place some blocking under the front of the washer. I did this so that I could access two screws on the bottom of the pump. First disconnect the wire socket connection to the motor. Make sure power is off before doing this. There is plastic clip holding the wires to the motor that may need a screwdriver to pry it apart for removal. There are two 1.5" long screws holding the pump to the frame that require at least 4" of space so that you can remove them with a socket. After removing the two pump screws I disconnected both pump hoses from the pump. This requires pliers for one clamp and screwdriver or nut driver for the other clamp. My machine originally came with one clamp that could not be removed, so I had to use a dremel with a stone to cut the clamp. You have to be careful to not damage the hose when cutting the clamp if it cannot be removed with tools. I replaced it with a 2" typical standard stainless steel hose clamp. Carefully wiggling the pump while pushing it to the side it will loosen up so that the front of the pump can be pulled up. One side needs to have the plastic plate pried apart from underneath and after removing it the pump will come free to lift out. Reverse the removal process for re-installation. It is a little tricky holding the squeeze clamp open while pulling the hose onto the pump, but it is not too difficult. Before putting the front panel on run one load of laundry to make sure there are no leaks. Once you find there are no leaks, then tilt the machine up and back to reattach the front panel. It is much easier to do it this way than with the machine on the floor since the panel screw are on the bottom of the panel at floor level.

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

Removed top lid (only to be able to remove pressure sensor hose easily). Removed hose clamps and tied the ends together in order to keep in loose position. Then squeezed the damaged hose up between sidewall and tub to remove pressure sensor rubber pipe. Installed Hose with clamps tied in the loose position with thin wire. Attached the pressure sensor pipe. Loosened the thin wire holding clamps loose. Tested for leaks by running washer. Leak repaired.

Checked fuse with Volmeter, had continuity (acted as a short) not the problem. Disconnected Hot Surface Igniter 2 Position connector to check resistance for a range of 50-300 Ohms of resistance with Voltohm Meter. Meter read open (High Resistance). Removed Igniter by unscrewing 5/16" hex nut on igniter plate assembly and noticed silicon carbide element was cracked in the middle. Ordered a new igniter and noticed assembly was required. Be careful here as igniter element is fragile, also do not touch it with your bare hands. You have to lay down on floor to reinstall igniter assembly and you might want to practice anchoring the defective igniter to gain confidence. Finally with slow movements anchored new igniter assembly and turned on dryer. Watched igniter glow heating gas valve and heating gas flame returned. Dryer fixed for a few hours of study online and cost only $24, plus learned how the gas dryer works.

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Replaced drain pump took longer to soak up water than actually replacing the pump motor with mine having the pedestal underneath I did not have to tip the washer at all so it was fast and easy. Three screws taking the front cover off a screwdriver lifting the Rubber and sliding the motor off and pair of pliers 4 to hose clamps making it a breeze.

Took the old parts out and installed the new parts in , everything that you sent fit perfect!!!!!

Remove old filter
Vacuum out
Install new filter

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

Remove top,front and panels.change thermal fuse and outlet thermistor.

all that was required was to push the catch into the slot notools needed.