MLG2000AWW Maytag Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from Homewood, IL
- Parts Used:
- 4391996
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
boken igniter
Quick and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Newfane, NY
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was not firing consistently
Parts came as ordered and in really good time. The valves were very easy to install, just a matter of removing lower housing and the two screws holding in the old valves. The plug and play, no calibration needed and the dryer works like new. Very easy fix and the instructional videos were very helpful. Saved a lot of money doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Monroe, MI
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Gas valve will not light
Replaced bad coils
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from macomb, MI
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
need to replace the coils
Removed 2 screws at the lint filter, unplugged dryer, next I popped the top off with a standard screw driver lifted the top all the way up and secured it from falling back down, used a 5/16" nut driver to remove the top 2 screws holding the face on, disconnected the door switch, pulled the face panel off and set it aside, then I removed the tension pulley on the bottom and took the drum out, unscrewed 2 screws holding the coils removed the old coils and installed the new reconnected the leads to them, vacuumed out the cabinet and motor, inspected all moving parts for wear, including the belt, reinstalled every thing in reverse order, had job complete and ready for clothes in 9 mins, it helps to have your son/daughter hold the drum against the back wall while reconnecting the tensioner and belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darwin from Meriden, CT
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
I have a Maytag gas dryer, it runs but it dud'nt get hot....
First I opened the back panel & check the fuse with multi meter tool ( put in ohms & set it in 200K) & the fuse is Ok, try to run the dryer while looking in the flame dock & the burner starts & had a fire till about 2-3 mins. & flame comes off, what I did is I open the front door to access into the gas burner, check gas valve coils with multi meter tool for continuity & found out that one of the coil doesn't have continuity. I ordered a pair of coil that is located on top of the gas valve on this site & unexpectedly it came in the next day, WOW! that's a fast delivery I was very pleased w/ the service, come home from work & installed it right away & it took me 5-10 mins. Put back everything & try to run it & it works properly. So happy with & my wife as we'll, thanks for the great fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from ALBANY, TX
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Took too long to dry
Watched the video and followed the directions. It was pretty easy, but, I ended up having to call the repairman anyway. After the heating element was put on we put the cycling thermostat on. I didn't know it, but I put some wires on upside down. I bought a heating element, a cycling thermostat, thermal fuse, and a thermal cut off kit. All that, and I still had to pay a repairman. If you're good with wires, or have some knowledge of appliances this is an easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Bedford, TX
- Parts Used:
- 12001541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
It was making a lot of noises
IT was good My husband fixed it .sorry we didn't take video but it is working alright. Thank you
Was this instruction helpful to you?
Thank you for voting!