MLE20PDAYW0 Maytag Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ricardo from DETROIT, MI
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
It wouldn't drain anymore so I started looking on the internet for a solution. I came upon this website and found the part I needed. It was easy to install. It fixed the problem I had with the washer.
I just took off the old part and installed the new one. The new part was a bit different.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BOILING SPGS, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
My dryer was squeaking with an occasional thump
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from HUNTSVILLE, AL
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Sqeeking noise fron old worn belt and rollers
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from Garland, TX
- Parts Used:
- 280114
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Broken Drum Belt
Just like the video, just followed the video
Thanks,
Thanks,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from LITTLETON, CO
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
pump would not pump out the water in the tub
just changed out the pump. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from wilton manors, FL
- Parts Used:
- WPW10730972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
The rubber boot assembly is not the same configuration as the original equipment.
I had to cut new slots in the metal base of the machine cabinet to accommodate the different configuration for the rubber boot assembly. Thankfully the new pump works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from BOYLSTON, MA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
No problem as instructed.
As video instructed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from TARPON SPGS, FL
- Parts Used:
- W10822553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Spring balanced tub violent shake on spin
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from REXBURG, ID
- Parts Used:
- WPW10730972
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Washer would not drain flashing f-21 code
Took it old pump and replaced with new pump VERY EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from Vernal, UT
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A hole in filter
Remove old filter
Vacuum out
Install new filter
Vacuum out
Install new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- connie from NEWARK, OH
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
rollers on the tub had worn and the tub was no longer balanced.
sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from LEMOORE, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Coin op Whirpool Dryer Broken drive belt and frozen drum wheels
Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HUNTINGDON VY, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad screaming noise
Replaced 4 wheels and new belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vern from LAREDO, TX
- Parts Used:
- W11366249
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Drain/Pump bellow (washer tub to pump hose) punctured. Leaked excessive amount of water.
Removed top lid (only to be able to remove pressure sensor hose easily). Removed hose clamps and tied the ends together in order to keep in loose position. Then squeezed the damaged hose up between sidewall and tub to remove pressure sensor rubber pipe. Installed Hose with clamps tied in the loose position with thin wire. Attached the pressure sensor pipe. Loosened the thin wire holding clamps loose. Tested for leaks by running washer. Leak repaired.
Was this instruction helpful to you?
Thank you for voting!