MLE20PRAYW0 Maytag Washer Dryer Combo - Instructions

this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the company was a perfect fit.

The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.

I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.

Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair

Couldn’t see exactly where it was coming from. Checked the bellow and it looked ok. Took this hose off and it was kinda chewed up a bit where it connects to the tub. Not bad but enough to make it leak. Ordered the new one. Took forever to get here thru fed ex smart post. Repair takes longer to get the panels off than it does to put new hose on. Hope this helps someone out there.

On this model do not try to remove the back. You must remove the bottom front panel and the lint screen unit. You can then loosen the heat coil assembly and rotate it to get to the high-limit thermostat and the thermal unit. I replaced both because I bought the kit. It actually took me longer to clean out lint than it did to replace the parts. A simple remove of the parts with a 1/4 inch nut driver did the trick. Now my dryer works fine.

placed sprayer arm in position and twisted it into position, about a 1/4 turn, snaps into place. total of 15 seconds!

I had to cut new slots in the metal base of the machine cabinet to accommodate the different configuration for the rubber boot assembly. Thankfully the new pump works like a charm.

Watch the video. Very, very easy

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.

It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.

The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order

I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones.