WM3997HWA LG Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roger from LA CROSSE, VA
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
soap dispenser broke
just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobbie Joan from ASHEVILLE, NC
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door would not close because the part that was in the door that held it closed kept falling out.
Order the part through PartsSelect. It arrived in a few days and I (an 81 year old woman) replaced it within minutes with no help needed. It was super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALEX from TULARE, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Washer was not draining
It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergio from MADISON, WI
- Parts Used:
- MCD62387101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
CONNECTOR NOZZLE, LEAKED
Took off top of washer to get access to connector nozzle, which is on top front of washer rubber boot. removed old nozzle, installed new one. Easy peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B from HEATHSVILLE, VA
- Parts Used:
- 4036ER4001B
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Seal on front loading washer failed, causing basket bearings to fail.
I removed the tub. Thin included disassembling the washer and disconnecting various hoses electrical connectors to facilitate the removal of the tub from the machine.
Once removed, I separated the two halves of the tub and removed the metal basket to gain access to the bearings and seal.
Removal of the bearings was much harder than expected as they were very difficult to drive out of their pressed in mounting.
I finally was able to remove the bearings and fabricated a press using a piece of all thread and two steel plates to install the new bearings and seal.
I would not attempt to do this again with the proper bearing pullers and an official press to install the bearings gently without beating the tub housing.
This repair I feel is beyond the scope of your average DIY. The bearings can be damaged easily without the specialized tools to install the components.
Once removed, I separated the two halves of the tub and removed the metal basket to gain access to the bearings and seal.
Removal of the bearings was much harder than expected as they were very difficult to drive out of their pressed in mounting.
I finally was able to remove the bearings and fabricated a press using a piece of all thread and two steel plates to install the new bearings and seal.
I would not attempt to do this again with the proper bearing pullers and an official press to install the bearings gently without beating the tub housing.
This repair I feel is beyond the scope of your average DIY. The bearings can be damaged easily without the specialized tools to install the components.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from GREEN BAY, WI
- Parts Used:
- 4036ER4001B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
My front load washer was making a loud roaring sound while spinning out the water
The repair went good but time consuming. I replaced both inner and outer tub bearings along with the tub seal. I removed top by removing two screws in back then pulling back slighty then lifting up. I removed soap tray by pressing down tab and pulling out. Loosened soap dispenser and folded back on top. I removed control panel then front door panel. Remove back panel. Remove motor and shocks and hanging springs which there are two. Disconnect the hoses attached to tub then pull the tub. Remove screws holding the tub halves together. Use punch to remove bearings. NOTE: If you put the bearings in the freezer prior to installing, they go in much easier. I used the old bearing, set it on the new bearing then I tapped the old bearing so not to damage new bearings. I replaced the seal then put everything back together. Not difficult but time consuming.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- willard from RIVERSIDE, CA
- Parts Used:
- 4280EN4001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Drum was making a very load grinding sound
I took the washer completely apart and ordered any parts that looked worn and put it back together. It’s working like new and will last for a few years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from ORLAND HILLS, IL
- Parts Used:
- 383EER3001J
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Could not remove one of the pins
Removed the front and rear covers ,the control panel , removed the shock absorber pins and shocks installed new shocks and reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from COLUMBUS, OH
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broke cold water inlet while moving
Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from MARYVILLE, TN
- Parts Used:
- 383EER3001J
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Spin cycle was shaking my house LOL
Just like it shows on You tube but one of the shocks did not come with the plastic pegs so i used the old one. I need to order the springs now and replace them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GOLD BAR, WA
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Soap dispenser
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from KERRVILLE, TX
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hot water valve was leaking
After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from CLEVELAND, TN
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The hot water inlet valve started to leak.
To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christen from HUMBLE, TX
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
The hot water valve was leaking
It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.
Thank you again for an amazing experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from SHELTON, WA
- Parts Used:
- AHL72914401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Displayed LE error even with a couple of pair of socks as a load
I ordered the Rotor Assembly and Sensor Assy..
Rotor Assy. was not the problem.
1 - 17mm bolt in the center of the rotor assy.
6 10mm bolts to take off the Stator assy.
once you have the Stator assy off, upplug the sensor assy and release the clips on the sensor assy. and remove.
Install the new sensor assy. and plug the electrical connection back in.
replace the 6 bolts and screw the bolts evenly around the Stator.
replace the Rotor Assy. and secure the 17mm bolt.
Replace the back cover (4 - philips screws.
Do a test load.
Rotor Assy. was not the problem.
1 - 17mm bolt in the center of the rotor assy.
6 10mm bolts to take off the Stator assy.
once you have the Stator assy off, upplug the sensor assy and release the clips on the sensor assy. and remove.
Install the new sensor assy. and plug the electrical connection back in.
replace the 6 bolts and screw the bolts evenly around the Stator.
replace the Rotor Assy. and secure the 17mm bolt.
Replace the back cover (4 - philips screws.
Do a test load.
Was this instruction helpful to you?
Thank you for voting!