WKGX201HBA (ABLEEUS) LG Washer Dryer Combo - Instructions

Unscrewed the dryer latch on the dryer (not the piece on the dryer door) and screwed in the new piece! Bam, done and done. The ordering process was a snap, very friendly on the phone. She even emailed me a picture of the part before I ordered to make sure it was the right one, and was so patient with me, while my kids were sort of loud in the background. Thanks PartSelect.com, your part is quality and employee rocks.

It only took about 5 minutes to fix the problem. Took out two screws, removed old part, put the new one on and replaced the screws. Works great now!

UNPLUG WASHER.Unscrew 4 screws holding silver plate at back of unit. Remove plate to expose inside of unit. Locate drain hose at bottom of washer tub. Hose connects at front drain, bottom of tub, and at rear at the pressure sensor. Front and rear simply slide clamps down by grasping clamp tabs and sliding clamp off connection point. Disconnect from tub bottom by loosening main clamp with Phillips screwdriver and pulling downward. Have a towel handy as there will be water in the hose, and it will pour out when removing it from the unit. Installation is the reverse of removal. ATTACH THE HOSE ASSEMBLY TO THE DRUM FIRST, THEN FRONT, THEN LASTLY REAR. This order is the easiest way, otherwise you will spend extra minutes trying to get the tub connection to seat properly. Plug it back in (duh), then you're good to go for another 4 years or so until another hole wears in the hose. I have performed this repair on 3 different units, with 4 years being the average lifespan of this part.

Easy repair, more time spent de-linting the inside of the machine and the duct system.

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.

First I just replaced the ignitor on a hunch, (disassembly was easy once I saw the video) I also examined the high limit thermostadt and found it was tripped, so I reset the button. the dryer fired up, but soon the thermo tripped again. I found that I could reach it with my arm placed in the inspection port,( about a 4 inch diameter pop out) make sure you unplug first, find the button near the ignitor, and pop it in. the high limit thermo was only holding a few seconds, so I decided to replace it, and did a "shot-gun" approach, replacing all thermos and thermisters at once, only about 35 bucks delivered...BTW, PartSelect shipped them to me at the speed of light.....one day ! Ireplaced all thermos and did and extra scrulpoulous cleaning of the vent. NOTE: it is completely possible that ahe only problem was a reduced vent capacity cmbined with summer heat leading to tripping the high limit thermo....however the thermo was tripping waaaay too easil in my opinion. Anyway, I celebrated doing 10 loads of piled up laundry, and basking in the glory of my wife's admiration for saving a $1000. appliance replacement. "how did you know how to do this honey?" "yoir so smart" (i did'nt tell her about the PartSelect video)

Removed Top, then front and drum. Parts easy to access once drum is out. Recommend reading up on drum replacement. Would appear that all repairs will require taking it out.

Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (to my surprise without any extra screws or parts left). Fairly easy job, just time consuming.

I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.

well after hurricane sandy we had a family of 5 stay with us. after the storm we retrieved most of thier clothing and started washing. the machine worked off of a generator for 4 days almost around the clock. overloaded at times i might add. these folks lost just about everything. my wife noticed a noise i opened the machine and saw the cracked drum. i ordered a new one from you guys and saved the $900 on a new machine. together we breathed new life into it. thanks!!!