Models > GCWL1069CS3

GCWL1069CS3 LG Washer Dryer Combo

Jump to:

Find Part by Name

Most Popular Parts for GCWL1069CS3

Viewing 12 of 104

Water Inlet Valve - Hot

★★★★★

(2)

$36.42

The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with wat...

Order now and your part arrives by May 9

Magnetic Door Plunger

★★★★★

(3)

$19.63

This magnetic door plunger is a genuine replacement component designed to keep the washing machine door slightly ajar when not in use. By allowing air circulation, it helps the inner door and tub seal...

Order now and your part arrives by May 9

Tub-to-Pump Drain Hose

★★★★★

(1)

$56.24

This hose has bellows to allow for flexibility during the wash and spin cycles.

Order now and your part arrives by May 9

Washer Gasket

$25.10

This rubber tub seal fits between the front and rear halves of the washing machine’s outer tub to prevent water leaks. It helps maintain proper washing performance and may need replacement if you noti...

Order now and your part arrives by May 9

Washer Tub Bearing, Rear

$46.07

This tub bearing is for washers. Tub bearing supports the spin basket shaft at the tub. Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.

Order now and your part arrives by May 9

Inlet Valve Assembly

$132.20

This water inlet valve controls cold water flow for the bleach dispenser and prewash cycles. It has one standard hose inlet and three angled outlets—two to the right, one to the left. Designed for sel...

Order now and your part arrives by May 9

Pump Filter

$25.10

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your wa...

Order now and your part arrives by May 9

Washer Tub Bearing

$57.30

Tub bearing. This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly.

Clamp Assembly

$21.82

The door boot seal clamp, also referred to as an outer door gasket clamp, holds the door boot in place in a front-loading washer. If your washer is leaking from the door and there are no signs of dama...

Order now and your part arrives by May 9

BOLT ASSEMBLY

$19.63

Shock Absorber

$56.24

Sold individually.

Order now and your part arrives by May 9

Clamp

$15.26

Order now and your part arrives by May 9

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for GCWL1069CS3

Viewing 10 of 10

Leaking

Fixed by these parts

How to fix it

Lid or door won’t close

Noisy and Marks Left on Clothes

Videos for GCWL1069CS3

Viewing 7 of 6

Replacing the Magnetic Door Plunger

Replacing the Water Inlet Valve - Hot

Replacing the Water Inlet Valve - Cold

Replacing the Washer Switch Assembly

Replacing the Inlet Valve Assembly

Replacing the Tub-to-Pump Drain Hose

Replacing the MOTOR

Installation Instructions for GCWL1069CS3 Provided by Fix customers like you

Viewing 3 of 94

Customer:: Omnitech from Warrenville, IL
Parts Used:: AGM73610701
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Door would not close

There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replac ... Read more

Read less

157 of 178 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Leslie from STOWE, VT
Parts Used:: 4738ER1002A
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

leaking tub-to-pump drain hose

Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.

52 of 72 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Sanjay from HOLTSVILLE, NY
Parts Used:: 5220FR2006H
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers, Wrench (Adjustable)

Water was filling continues even the machine was unplugged

I did repaired while looking at video at your site .thanks to your team ..

20 of 24 people found this instruction helpful.

Was this instruction helpful to you?