DLEX7900BE LG Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- NANCY from ATASCADERO, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was making a terrible sound.
An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RIVERSIDE, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Loud rumbling noise
Followed video provided on site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Michigamme, MI
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
thermal fuse went out
Watched a repair video. Very easy to replace, about an hour to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D Michael from Plymouth, IN
- Parts Used:
- 4581EL2002L, 4400EL2001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
noise when you ran dryer
Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omar from SILVER CITY, NM
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
CHANGED OUT MOTOR
FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from CUDAHY, WI
- Parts Used:
- 6323EL2001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
no heat
To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from DAWSONVILLE, GA
- Parts Used:
- 3911EZ9131X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Install aftermarket side vent kit
I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Whittier, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Thumping sound when dryer is on.
I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Marriottsville, MD
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Changed mottor
I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from Southbury, CT
- Parts Used:
- 4581EL2002L, 4400EL2001A
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Loud rhythmic knocking sound
You will need a helper. Dismantle the Dryer: Remove the screws that hold the top cover, front control panel, front door and front panel. Release the V-Belt under the drum. Remove the Drum. Removed and replace the 2 Front roller assemblies - these were completely worn. Replaced the 2 rear rollers (did not replace the rear roller axels as these were more difficult to remove and they were in good shape) and the V-Belt while I had the whole thing open. Use a shop vac and cleaned up the whole unit. It is so nice and quiet now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Los Altos, CA
- Parts Used:
- AJQ75298102
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
fractured, broken drum.
Easy repair, more time spent de-linting the inside of the machine and the duct system.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Boise, ID
- Parts Used:
- AJQ75298102
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Hole in drum
Found YouTube video followed it closely and did extensive cleaning. The lint on the felt of the drum was causing a rough rotation as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Staten Island, NY
- Parts Used:
- 4400EL2001A, AJQ75298102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
thumping noise (cracked drum)
well after hurricane sandy we had a family of 5 stay with us. after the storm we retrieved most of thier clothing and started washing. the machine worked off of a generator for 4 days almost around the clock. overloaded at times i might add. these folks lost just about everything. my wife noticed a noise i opened the machine and saw the cracked drum. i ordered a new one from you guys and saved the $900 on a new machine. together we breathed new life into it. thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Fremont, OH
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Loud squealing noise coming from dryer.
Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (to my surprise without any extra screws or parts left). Fairly easy job, just time consuming.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Iowa, LA
- Parts Used:
- 4400EL2001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt slipping, drum will not turn
I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.
Was this instruction helpful to you?
Thank you for voting!