DLE3400W LG Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from Manchester, IA
- Parts Used:
- AGM75510755, 4400EL2001F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Drum bearing had gone bad causing excessive noise
Followed the repair video provided in the order confirmation email. Was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MADISON, AL
- Parts Used:
- ADQ56656401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked lint filter
Simple replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from RENO, NV
- Parts Used:
- 3045EL1002P
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum cracked
Repair was easy, but the part does not come with directions. It is pretty self explanatory if you are used to taking things apart and fixing them. Otherwise there are YouTube videos you can pull up. Dryer runs like it is new again though and it was way cheaper than buying a new dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D Michael from Plymouth, IN
- Parts Used:
- AGM75510755, 4400EL2001F
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
noise when you ran dryer
Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- temeaco from TULSA, OK
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Locker assembly broke
Just unscrewed the original lock and screwed the new one on it was very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raul from CYPRESS, CA
- Parts Used:
- 4774EL2001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer door hinge broke.
Followed YouTube video repair process. The only problem is that the door hinge has plastic bushings attached. A couple broke and the parts listing does not show the bushings, nor does the hinge come with them. The door is a bit loose without them. Nonetheless, the repair did the job for now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omar from SILVER CITY, NM
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
CHANGED OUT MOTOR
FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from DAWSONVILLE, GA
- Parts Used:
- 3911EZ9131X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Install aftermarket side vent kit
I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RIVERSIDE, CA
- Parts Used:
- AGM75510755
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Loud rumbling noise
Followed video provided on site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from MAPLEWOOD, NJ
- Parts Used:
- MDS47263101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Gasket
I'm a technician Mechanic using my skills for fix that's
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from CUDAHY, WI
- Parts Used:
- 6323EL2001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
no heat
To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Whittier, CA
- Parts Used:
- AGM75510755
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Thumping sound when dryer is on.
I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Marriottsville, MD
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Changed mottor
I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rand from Panama City, FL
- Parts Used:
- MEA49050001, ADQ56656401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lint and guide filter had become damaged
Really easy to do! Unscrewed 4 screws, pulled flap on bottom of inside guide out. Then gently shake assembly to loosen from dryer and pull up and out! Then based on the assembly can replace front or back or both. They snap together! Put assembly replacement back in and close flap and secure in place with the four screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Grosse Pointe Farms, MI
- Parts Used:
- ADQ56656401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One corner of th elint filter kept sticking up and catching clothes on it.
R&R new lint filter.Old filter appears to have been made improperly and the out frame was warped raising the cormer that kept catching the clothes.
Was this instruction helpful to you?
Thank you for voting!