2671532413 Kenmore Washer Dryer Combo - Instructions

Watched the video on YouTube and everything went great!

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

I watched video supplied from parts select, only took about 30 minutes, hardest part was putting belt back on, couldn't fit hands in easily, but once I did it, dryer is like new, can't hear a thing.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

Took off the top cover then took off the front panel and installed the new coils on gas valve.

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.

I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes

Replaced with the new part that I ordered from partselect.The washer works good. Thank you.

watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe

I only had to replace the "plastic" knob on my dryer. This required no tools- just push on to the stem. This part needs to be improved... should be made out of something other than plastic because this gets a lot of wear. I was very pleased with how fast I was able to order & receive my part shipment. I shopped around for this part & your company beat any other price on the market. THANKS!

Removed door strike and latch, replaced, works like new.

unplugged old switch and installed new one. it took 5 minutes to do. 20.00 saved me 400.00 on a new washer.

Switch off the circuit breaker supplying power to the dishwasher.

Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.

Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.

Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.

Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.

Snap the switch (or switches) back into place in the cradle.

Replace the spring activator along with the plastic sheeting and screw that back in.

Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.

Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.

Switch the circuit breaker back on and give it a whirl. Enjoy!