2661532513 Kenmore Washer Dryer Combo - Instructions

I reviewed the video instructions on the website; these were invaluable to understand the task. Since the dryer drum had to be removed to replace the thermostat, it was prudent to replace the drive belt at disassembly. Great job on the videos to see the extra effort required to install the new belt around the tensioner pulley while supporting the drum. I will use this site again when a need arises, because they are quick to ship the ordered part(s) and help the DIY handyman make repairs via the videos.

When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!

I wanted to fix the cheapest possible problem first which was the thermostat.

Got the dryer apart and it was the wrong thermostat for the dryer, which was good news! I looked in inside floor of the dryer cabinet and saw alot of tiny "springs". Couldn't figure how they got there.

Turned out they were coils from the heating element. Must have burnt out and fell free from the element. So I ordered that and replaced it.

I want to say that I'm in NJ and I ordered that thermostat and got it in ONE DAY! Thought that was too good to be true but when I ordered the heating element THAT CAME IN ONE DAY!

I don't know what kind of people work in the shipping department but they are awesome! You really made the difference on this job.

So did the info on your website. I've never even seen a dryer apart before. It was a piece of cake thanks to you guys. You just saved me about $500.

1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.

Took the few screws out replaced the part then put it back together.

Took the top and front end of the dryer off. Took the old slider spacers off and installed the new ones. I replaced all four of them even though only two was bad. While I had the dryer open I decided to use my shop vac to clean up the lint that had accumulated there. Replaced the front and the lid plugged it up, hit the start no noise just like new.

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you

There are 2 switches that should be pressed in when you move the handle to lock door, the switches usually go bad with time. Just take the six screws off on the inside of door, then remove screw on the underneath part of handle. The switches are located on the top part under a piece of 1 inch metal plate held in by a screw, remove that and you'll see the 2 switches, test the button on each one to see if it goes in and out, you'll hear the click to. Just unplug bottom first then the top if you need to replace the top one. Thats it.

Washer/dryer belongs to a friend. Originally, the problem was that the dryer wouldn’t heat, so I opened it up, and removed the drum thinking it might be the heating element. It wasn’t, and the ohm reading confirmed this. It turned out to be a burnt wire connector to the element ( unknown to me, and found out later, was that the start switch had remained continuously in the down position because the switch was pressed too far down and thus remained locked “on” in place under the surrounding cabinet frame. This, in my opinion, caused for a continual call for heat and thus burnt the wire.)

I replaced the burnt wire/connector and reassembled. Now the dryer would heat, but would only run if the start button was continually depressed. Let go of the button, and the dryer stopped.

Repair pros suggested a new start switch. I bought a new start switch along with a new interlock switch (it basically shuts off dryer if belt breaks because lack of a belt releases pressure on the pulley that keeps switch depressed.) Apparently they can go bad, too.

It turns out neither of these switches were bad. Instead, upon further inspection, after the first installation of the drum belt, the L-shaped bracket which holds the pulley for belt tension became dislocated from its correct position and was not allowing for the depression of the interlock switch, causing the dryer to “read” broken belt, and thus, not run.

I loosened the motor bracket to allow placing the bracket in the correct position. Reassembled and all was good.
PSA - almost every sheet metal edge is razor sharp.
In the process of returning parts. Now in the process of returning parts.

My dryer knob broke on the timer cycle switch so I ordered a new one along with a new dryer knob which didn't fix the problem, then I ordered the start switch and all I had to do was remove the back of the dryer where all the knobs are located and remove the start switch by turning the start switch to remove it, replace it with the new one by turning it till it clicks in just like when you removed it, put knob back on the front. However that didn't fix my dryer either so I ordered the thermal fuse and switched it out and that was what started the dryer back up. It is located on the back all the way to the bottom where the electrical cord is. Remove the cover and locate the fuse. Use a pair of pliers to pop it out and push the new one back in.

Reviewed your website for problem symptoms for top loading washers not agitating and possible solutions. Purchased the lid switch wiring harness. All I needed was a painters 1" putty knife, wire cutters, Philips head screwdriver, (2) electrical connectors (crimping type), crimping tool, and electrical tape. Very easy installation and problem was solved. Recommendation, the wiring harness should come with electrical connectors (crimping type). The installation video on your website was a big plus in making this small project a success

First I called to get help with the right part and they told me I needed the pus-to-start-switch. It came in and I called my handyman Ed to install it. I am happy with your service. I dont install but just got the part in.

snapped in new latch

watched the video, and it was simple!

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks