36371542211 Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Victor from NAPA, CA
- Parts Used:
- WE03X37317, WE3M26, WE03X37318
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Excessive noise during drying cycle
My advise is to watch the video prior to starting, while fresh in your mind start the repair, it's so simple, I actually thought I was the Maytag Repair man,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from BELFORD, NJ
- Parts Used:
- WE4M415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Switch not working.
Open the door and removed the part. Installed the new part and started the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Crown Point, IN
- Parts Used:
- WE3M26, WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer making high pitch squeal
Remove top (2 screws) and front (2 screws), snap out old drum bearing, put new slides in new drum bearing and install in dryer. Reinstall front and top of dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from PHENIX CITY, AL
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I broke the door strike on the dryer.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from WACO, TX
- Parts Used:
- WE2M302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Reversing the dryer door.
Removed 4 #1 Philips screws from 1side and add to the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Austell, GA
- Parts Used:
- WE04X25996
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Igniter burnt out
The bracket on the part supplied was different than the original. The wire connector was also different. The bracket had to be drilled for a hole to match the original. The connector had to be cut off and the wires soldered together, then tied off to the frame to keep them away from the flame. The repair works like new but not the simple plug and play I was expecting. In all fairness the exact model number was not available, probably since the appliance was 24 years old, so I chose the closest model number with the picture that looked like what I had. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael E from Victoria, TX
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Dryer Belt Broke
After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.
I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.
I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.
The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.
The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.
Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.
Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.
Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.
I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!
I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.
I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.
The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.
The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.
Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.
Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.
Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.
I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuc from WOODBRIDGE, VA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from EPHRATA, PA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tod from Cherry Valley, CA
- Parts Used:
- WE03X29897, WE3M26, WE03X37318, WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud squeaking
remove to screws in front to take of top. Then remove two screws holding the face on. change parts re assebmle. extra hands nice for holding drum while remounting face. Nice and quiet now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laurel Springs, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from BOCA RATON, FL
- Parts Used:
- WE03X37317, WE3M26, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front Drum Bearing Cracked. Bearing Slides worn or totally missing
I followed the video instructions provided to me by this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD from MURRIETA, CA
- Parts Used:
- WE03X37317, WE3M26, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The old drum bearing was worn down due to years of usage.
Remove the old bearing assembly and Replaced with the new bearing assembly with new bearing slides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doreen from fall river, MA
- Parts Used:
- WE03X37317, WE3M26
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
squeeking and clothes getting cought
I followed the instructional video that was given online. The parts fit well, and was easy to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francisco from WEST COVINA, CA
- Parts Used:
- WE4M181
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
was not heating cheak parts select they recomended to purchaged the thermostat check vidio for installetion now working fine thanks
watched vidio from the site.just follow the instructions, And was able to fixed the problem.
Was this instruction helpful to you?
Thank you for voting!