11080754003 Kenmore Washer Dryer Combo - Instructions

one of ears that holds filter was broken leaving a small gap so lint went into duct work so i replaced the cover and filter is now held in place letting the filter do its job trapping the lint

Replaced AGITATOR DIRECTIONAL COGS (4) looking instruction video . Replaced CLUTCH LINING KIT following video of this site "WASHER REPAIR-REPLACING THE CLUTCH ASSEMBLY". Replaced SEAL, GEARCASE COVER and NEUTRAL DRIVE ASSEMBLY as follow: 1)CLUTCH Assembly and motor removed, took the GEARCASE on a bench vise to hold in place and the long shaft up side. You can get help from other person to hold secured in place instead a vise.2)Following a youtube video I tested gearcase with a reversible drill using DIRECT DRIVE MOTOR COUPLING PART next To transmission side instead of electrical motor. Drill turning counter clockwise drive the long shaft oscillating (it agitate via agitator cogs). Drill turning clockwise run the exterior sleeved part around shaft (upper side of metal gear inside gearcase and fixed on top to clutch to get washer spin). My experience was didn't rotate so we had to take apart gearcase cover.3)Unscrewed and removed gearcase cover. Cover was sticked by old seal gasket so a screwdriver helped me to remove it.4)Cleaned joint removing old gasket.5)Repeating drill test I realized big nylon gear did'nt rotated and removed uppercut clip with pin pliers with care for not lose the pin. Removed the next washer, the plastic gear and found a plastic part with a tooth broken. This part is with NEUTRAL DRAIN ASSEMBLY so replaced assembly following part instructions. I recommend take pictures in order to reassemling and use ALLEN WRENCH 5/32'' inches.6)Fill up to half of gearcase with 16 ounces (about 1/2 of case) of gear oil supplied by PARTSELECT or automotive gear oil SAE 85w90 or SAE 90.7)Replaced SEAL, GEARCASE COVER. HARD TO REMOVED AND REPLACE! Take care not break!. I had to use a piece of metal tube and a vise.8)Applied automotrice black seal gasket silicone around the cover joint and case.9) Replaced the cover and reversal instruction video.THANKS to this site I get excellent service and Enjoyed with my toy.

I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.

Removed screws on top of machine to remove the control unit out of the way. Then used large regular screw driver to pry out the two clips that hold the back of the washer tight to the top frame. This allows the back to come away from the machine enough to get the water inlet valve free. Didn't have to remove the bolts at the bottom of the back of the machine (they were pretty rusty) Just removed the single screw holding the water inlet valve in place, slid it down and away from the back cover and could fish it out to the side and disconnect the hose (with plyers) and slide off electrical clips (make a note of which clip goes to which valve.) I removed the part first so I could make sure I was ordering the right one. When the part came (very promptly by the way) it went back together easy. Only question was regarding reinstalling the wires since I didn't mark which way they went. I knew which one went on the Hot and Cold but didn't know if it mattered which clips went on each terminal. Figuring it was AC guessed it didn't matter so put it together the way the connectors seemed to want to lie naturally. Put it together making sure no hoses or wires where pinched or rubbing against sharp edges. Replaced the rubber washers in the hoses and made sure the hose connectors turned freely (they had been rusted a bit and didn't turn on the hose freely and I think this was the start of the cross threading problem) This time the hoses went back on very easily, screwed them hand tight not forcing anything at any time (DIDN"T USE PLIERS!). Tried water and no more leaks. Washer filled faster also, think this was because the screens on the water valve were plugged. I'll have to remember to take the hoses off and make sure the screens are clear every couple years or so. If you are having slow fills, suggest you check this first before tearing in to the machine.

First, let me start off by saying - this part wouldn't normally break. Because it's a stackable, and my dryer motor went out, the repair company had to move the entire unit from the cubicle. When the repairman tried moving it by using the washer lid ... lets just say he broke the clip. And then we could never get them to come fix the part they broke!

So, I finally ordered the part myself after studying schematics online. I am not a repair person. So, if I could figure this out - anyone can.

Take the middle cover between the washer and dryer off. There are 3 screws holding that panel on. Set the panel and screws aside. There are two "S" shaped clamps at the back. Lift (hard) the front of each one. They will snap free - freeing the whole top of the washing machine. The top has the lid connected. Pull the top towards the front and then rotate it counter-clockwise. It will come right off. This will free up the area the clips go on.

Take the lid completely off to get it out of the way. The clips fit in the holes on the front left and front right. The large square side goes up, and the small side snaps into the hole on the base. Make sure the groove is facing forward for the top cover to slide into. To get the clip to snap into the hole, put the front side down, and push (really hard) on the back side - the side towards the back of the washer. It should snap into place with some pressure.

Now, just put the top cover (with the lid attached) back on, rotate it clockwise, re-clamp it down and replace the middle panel and 3 screws.

Easy, right?

Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

Removed the rinse dispenser from Agitator. Unbolted and removed agitator from machine.
Directions said remove upper agitator by pulling apart. Had to brace bottom with both feet, and lift straight up. Came off. Replaced 4 cogs, re=assembled and re-installed.

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!

I found a video tutorial that explained the three things that are usually the problem when a dryer stops working. This showed how simple the task is. I used a multimeter to check the switch, to make certain that this was the part that needed replacement. This was part of the tutorial, as well. I ordered from PartSelect because it was recommended to me by an application that I use to find places where items are less expensive. The correct part arrived in a few days and it worked fine. I'm not a handyman by any means, but the tutorial showed exactly what needed to be done. It appeared simple and it was.

REMOVE THE PANEL BETWEEN THE DRYER (above) and washer (below) two 3/8" metal screws. Remove the panel in able to remove the top panel of the washer. remove the top panel of the washer by releasing two screws in rear of washer, pull cover to front , unplug old lid switch. Put top panel on flat surface upside down. replace lid switch and replace the panel and BOB'S YOUR UNCLE. It is a lot easier than it seems.

My dryer started making a loud rumbling and clanking sound and I didn't know what was wrong.

First I pulled it away from the wall and disconnected the power cord. I loosened the four nut/screws across the top of the rear of the dryer with my adjustable wrench then removed them with the flathead screwdriver. Then from the front of the machine, pulled the top of the dryer towards me, freeing the top and removed it. I could see one belt towards the front of the machine that appeared to be intact. I plugged the dryer back in and ran it... It spun but continued to clank and rumble. I noticed a "groove" near the rear of the drum and didn't see a belt there so I assumed that I needed the rear belt and ordered a replacement. I WAS WRONG. It turned out that there is actually only ONE BELT on this machine, that in fact I needed replacement DRUM WHEELS.

Next, I unplugged the power cord again and then I removed all twenty some-odd screws from the rear of the machine... which was POINTLESS as it only gave me access to the heating element, so I replaced this and all the screws.

I then removed the inside top nut/screw from the front panel on both the right and left inner lip. The panel then lifted up and off of the machine...only connected at this point to the rest of the dryer by the wires.

I made a schematic of the wires and which color was connected where, and then only removed those that were necessary to detatch the front panel completely from the dryer (so I could easily replace them properly later).

I noticed at this point that the belt was still functioning (although was cracked and needed replacing soon anyways)...but that the bottom drum wheel had worn itself down on the inside (where it rests on the axle)...the rubber around the outside was still good... but the whole wheel needed replacing. The side drum wheel (same part number as bottom) appeared to be fine.

I ordered replacement DRUM WHEELS (they sell them in packages of two only).

When the wheels arrived, I got down on my hands and knees and noticed how the belt was connected to the drive spindle of the motor... by a spring levered plastic wheel... very simple. Push the spring lever towards the drive spindle of the motor...loosening the belt. Then removed the belt from the motor, relaxing the spring and the belt came off, hanging only around the drum of the dryer.

Without tension on the spring levered plastic wheel, it came off of the bottom of the dryer completely. (If your belt has broken, you most likely will find this sitting on the bottom of your dryer...I will tell you how to attach it later on in this story.).

I carefully pulled the sides of the dryer case apart and slid one side of the drum forward out of the case...then slowly slid the other side of the drum out of the case...gently lifting up and out...completely removing the drum from the machine....setting it aside.

The dryer (inside the case) was FILTHY. I got out the handheld vacuum and cleaned it all out (finding a religous medallion, an earring, and over $2.00 in change). I vacuumed the inner bottom, sides, motor, and took advantage of vacuuming the inside of the lint collector as well... cleaning it up nicely.

The bottom drum wheel was attached by a triangular plastic clip (on both sides of the wheel)...I removed the plastic clip carefully by gently prying it off with the flat edged screwdriver... being careful not to break it. There was a LOT of hair wrapped around the axle near the triangular clip and used the pliers to pull the hair off...then removed the bad wheel..then the plastic clip behind where the wheel was sitting...and the hair there as well. I cleaned off the axle thoroughly, then did the same with the other drum wheel (even though it looked fine, I replaced them both.).

I set the old side wheel aside with the old (still useable) triangular plastic clips. In the future if one of the wheels goes bad... I'll have a replacement that will get me by.

Then I slid one of the NEW triangular p

easy three prong push-in,...

Safety First - I unplugged the power source. I removed the console by simply removing several screws. However because the nut fastening the resistor was in a really tight spot and I had little room to work, I decided to remove several screws from the back of the console to open it up. (This step is not necessary - but for me, it just made the job go quicker). I was then able to use my ratchet/socket set to remove the nut from the resistor. I then attached the wires from the timer to the new in-line resistor. I closed up the console, re-attached it to the dryer and DONE!!! The dryer works fine!!! By the way, the set is 25 years old. I initially thought it was the timer itself but after explaining the problem to Rebecca at this iste , she quickly identified the problem as the timer power resistor. Many thanks Rebecca??

First I pulled out lint catcher, you will see two screws ,removed two the screws on top ,( philips head screw driver) I than took a putty knife and pushed in the front of the dryer under the lid and lifted the top up, I than removed a self tapping screw on each side with a 5/16 wrench and lifted the front panel out. I than pulled out the drum and this exposed the two rollers, I than pulled of the nut locks with athe pliers , took off the plastic triangle snaps and pullled off the old rollers , replaceing them with the new ones,put the triangle locks on and that the lock nuts on , I than put the drum back in, than the front panel, replaceing the two self tapping screws , snapped down the top,replaced the other two screws again on top and replaced the lint catcher, I was done.

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.