1109875279A Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from Minneapolis, MN
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
No hot water flow, cold water flow very slow
It is sometimes tricky to figure out which screws and panels to remove to get to the parts you want to fix. Older Whirlpools used to have a lift up top that would allow access. This one required the back to come off (or at least partially off).
First, pull out the washer for access. Turn off water to the machine, and unplug the electrical cord. Remove the drain hose using a large pliers to pinch the clamp and then pull the hose off. Remove water lines at the back of washer, again with a large pliers (if needed). Remove two screws at the bottom of back panel. Remove two screws at the top corners of back panel that hold some sort of plastic hinge piece to the control housing. Remove two screws on either end of the bottom front of the control housing on top of the machine. The back can now be lifted free (with some effort) from the sheet metal tabs that hold the bottom of the back in place. Reach in the bottom side with the pliers and disconnect the large drain line clamp so you have more room to swing the back out. There also might be a little plastic thingy to twist out of a slot in the back (maybe a vibration damper?) You will see the water inlet valve just inside the back on the side. The inlet hose connections are actually a part of the inlet valve. It is now possible to reach in from the side and disconnect the small water feed line from the inlet valve with a pliers, and disconnect the electrical plugs from the valve. Remove the two screws holding the valve to the back and remove the valve.
Reassembly is actually easier than removal. Don't forget to replace the water hose washers or they will probably leak. If the hoses look bad, just buy a new set. They can be had quite cheap.
Good luck and prepare to be proud of how well your "new" washer now works and how much money you saved!
p.s. PartSelect Rocks!
First, pull out the washer for access. Turn off water to the machine, and unplug the electrical cord. Remove the drain hose using a large pliers to pinch the clamp and then pull the hose off. Remove water lines at the back of washer, again with a large pliers (if needed). Remove two screws at the bottom of back panel. Remove two screws at the top corners of back panel that hold some sort of plastic hinge piece to the control housing. Remove two screws on either end of the bottom front of the control housing on top of the machine. The back can now be lifted free (with some effort) from the sheet metal tabs that hold the bottom of the back in place. Reach in the bottom side with the pliers and disconnect the large drain line clamp so you have more room to swing the back out. There also might be a little plastic thingy to twist out of a slot in the back (maybe a vibration damper?) You will see the water inlet valve just inside the back on the side. The inlet hose connections are actually a part of the inlet valve. It is now possible to reach in from the side and disconnect the small water feed line from the inlet valve with a pliers, and disconnect the electrical plugs from the valve. Remove the two screws holding the valve to the back and remove the valve.
Reassembly is actually easier than removal. Don't forget to replace the water hose washers or they will probably leak. If the hoses look bad, just buy a new set. They can be had quite cheap.
Good luck and prepare to be proud of how well your "new" washer now works and how much money you saved!
p.s. PartSelect Rocks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Adrian, OR
- Parts Used:
- 285805
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
Refill valve leaked continuosly.
Removed the hoses from the inlet valve. Removed screws that hold control panel in place . Removed control panel which exposed two clips that hold the top of the back panel. Removed the ground screw freeing the ground wire, removed the plastic loom which holds a bundle of wires. I next removed the plastic plate that protects the fill valve from splashed water. Removed the screw that holds the valve in place, then removed the wires and the fill hose. Reversed steps to put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from San Diego, CA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The water inlet valve was defective
First I turned off the water to the washer and then removed the hot/cold water hoses going to the washer, unscrewed the water hoses from the washer, and cleaned the wire screens located immediately inside the inlet water valve. This did not solve the problem. Second, I loosened the hex head screws on the back panel of the washer. This allowed me access to the valve. I tested the valve solenoids with my ohm/volt meter and all checked out OK (but this did not make sense). Third, I surfed the web to find out if the symtoms of the washer's problem were the same as experienced by other people. I found several reports of the same symptoms, all which were solved by replacing the water inlet valve. This conformed my original diagnosis although the valve tested as OK. Fourth, I ordered the part from PartSelect, and removed the hose clamp and two mounting screws holding the old valve to the back panel of the washer and removed the old valves. Last, when the new valve arrived, I assembled the new backing plate to the new valve, attached it to the washer's back panel, attached the water hoses to the valve after fitting new rubber seals to the inside of the hoses, and reattached the washer back panel. The washer is working perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Sterling, CT
- Parts Used:
- 285805
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
My washing machine overflowed and flooded the basement
First, I unplugged it and disconnected the water hoses (the water has been off to it for days). Then, I tried taking off the back of the washing machine. This didn't work, and I actually ended up googling instructions and found pretty detailed, illustrated instructions at Popular Mechanics.
You need to unscrew the front panel that contains all of the controls first, flip it up, and unhook it from the back of the washer (via an electronics clip and 2 metal clips). The outer cover can then be taken off. I recommend undoing the internal hose next -- I used adjustable pliers to squeeze the connecter and loosen the hose. Then, unscrew the water inlet valve and take it off.
Putting everything back together literally just means reversing the instructions.
My washing machine is on a raise service, and I still haven't gotten the outer frame completely back in place correctly, but it's not touching anything or creating any problems. It's really only to safeguard parts anyways, so no worries if it's not perfect -- at least it works now!
You need to unscrew the front panel that contains all of the controls first, flip it up, and unhook it from the back of the washer (via an electronics clip and 2 metal clips). The outer cover can then be taken off. I recommend undoing the internal hose next -- I used adjustable pliers to squeeze the connecter and loosen the hose. Then, unscrew the water inlet valve and take it off.
Putting everything back together literally just means reversing the instructions.
My washing machine is on a raise service, and I still haven't gotten the outer frame completely back in place correctly, but it's not touching anything or creating any problems. It's really only to safeguard parts anyways, so no worries if it's not perfect -- at least it works now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from cleburne, TX
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
squealing noise, very little cold water to fill tub, hot water normal
turn off hot and cold water faucets,unplug the power,pull washer out to gain access to rear cover, remove the top control panel screws,push back and lift off, disconnect hot and cold water hoses from inlet valve and remove enough screws from the back panel to remove the valve, disconnect the valve from the tub fill hose (mine had a spring type hose clamp) note the orientataion of the hot and cold hoses and the solenoid connectors for the hot and cold sides,(mine is stamped in the rear cover)reconnect and reassemble in reverse order and check for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joselin from Port Saint Lucie, FL
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Only hot water would be dispensed into the washing machine
took off the rear panel and removed the existing inlet valve and installed the new one. Replaced the rear panel and the machine work better than ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Phoenix, AZ
- Parts Used:
- W11613302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door Gasket Broke into pieces
It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Port Arthur, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not latch closed when shut
Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- juan from los angeles, CA
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door catch. door wont close properly
i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Oakland, CA
- Parts Used:
- 285805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Leaky Inlet Valve
This is a very easy repair. After shutting off the water, removing the feed lines, and of course unplugging the electricity, all I had to do was: 1. remove two screws 2. flip the control panel up 3.unplug a wiring connection 4. pop two clips that hold the housing to the back 5. lean housing forward 6.unplug wiring at valve 7. remove fill hose 8. remove two screws. 9. toss old valve in the recycling bin (or trash depending on your area) 10. Reverse procedure using new valve. 11. wash clothes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margery from Lake Spivey, GA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the door catch was broken and I was using duct tape to close the dryer!!
This was a classic easy repair and I am sure saved us bundles on a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Alpharetta, GA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Part of the dryer door latch fell out and was lost. Needed to replace it.
When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Sterling, VA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Wasn't flowing cold water effectively
To Whom It May Concern:
I had issues with my washer not flowing cold water very efficiently.
I was convinced I was going to have to spend at least $200 to get
someone to fix it or buy a new unit. My friend showed me your site
and videos. I quickly found the part I needed, had full confidence
that my problem would be solved with that part and that I'd be able to
do it myself. I ordered the part yesterday, got it today, and
installed it in under 15 minutes (thanks to the excellent video).
What an amazing customer experience!!
This is the greatest buying process I've every had with an Internet
purchase....hands down!! You saved me a couple hundred bucks and made
it fun and easy for me to fix myself. You guys are the best. No
doubt about it.
Thank you so much, Jason
I had issues with my washer not flowing cold water very efficiently.
I was convinced I was going to have to spend at least $200 to get
someone to fix it or buy a new unit. My friend showed me your site
and videos. I quickly found the part I needed, had full confidence
that my problem would be solved with that part and that I'd be able to
do it myself. I ordered the part yesterday, got it today, and
installed it in under 15 minutes (thanks to the excellent video).
What an amazing customer experience!!
This is the greatest buying process I've every had with an Internet
purchase....hands down!! You saved me a couple hundred bucks and made
it fun and easy for me to fix myself. You guys are the best. No
doubt about it.
Thank you so much, Jason
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Shipshewana, IN
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water would not shut off after filling for cycles
I found the helpful video, after a bit of a struggle removing rear panel from machine!! I determined the problem of being the water inlet valve from prior troubles on a machine.
I removed the screws from bottom of rear panel,then the Phillips screws from the back of control panel. bumping the control panel towards the front of the machine dislodges it from it's slots. the control then tilts back on plastic hinges, exposing the clips that hold on the rear panel.Those clips are pried up and removed. dis connect the wire harness to control panel. A similar screw as the first removed at bottom hold the inlet valve on the panel.. two simple wire terminals are pulled off as well as a small water line. I did not remove the entire cabinet front as shown in the video as space did not permit it. Still easily reached. the reverse was done to install. The machines are heavy, do get help there.
I did not have it. Be certain to shut off water supply before beginning. Also, I forgot to reconnect the wire harness to control panel. you wont,RIGHT.
I removed the screws from bottom of rear panel,then the Phillips screws from the back of control panel. bumping the control panel towards the front of the machine dislodges it from it's slots. the control then tilts back on plastic hinges, exposing the clips that hold on the rear panel.Those clips are pried up and removed. dis connect the wire harness to control panel. A similar screw as the first removed at bottom hold the inlet valve on the panel.. two simple wire terminals are pulled off as well as a small water line. I did not remove the entire cabinet front as shown in the video as space did not permit it. Still easily reached. the reverse was done to install. The machines are heavy, do get help there.
I did not have it. Be certain to shut off water supply before beginning. Also, I forgot to reconnect the wire harness to control panel. you wont,RIGHT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Kohler, WI
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Plastic door latch was cracked.
I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!