Models > 11088732795 > Instructions

11088732795 Kenmore Washer Dryer Combo - Instructions

Jump to:

All Instructions for the 11088732795
106 - 120 of 946
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Alec from Indianapolis, IN
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
The top agitator was not spinning
I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from Apple Valley, MN
Parts Used:
285753A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
basket would not spin during spin cycle
Raised washer on cinder blocks high enough to get underneath, removed wiring, capacitor (because it got in the way), removed spring clips from pump, removed pump, no water spillage this way. removed clips from motor, removed motor, pulled old broken coupling rubber ring and plastic pieces out, used a spark plug driver to press new ones in place on the gear shaft and motor as they will fit tighter because they have a metal reinforcement that the original did not have, lined up the two halfs and clipped motor back on, cliped pump back on, reconnected wires again, lowered off the blocks and washed a couple loads that night.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Timothy from Kansas City, MD
Parts Used:
80040
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
agitator was making a large amount of noise
After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Mountain Top, PA
Parts Used:
285753A
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Coupling broke
After flipping the washer on it's side snap off the clips that hold the motor in place and discard the old coupling. The new coupling fits in very snug some may need a little persuation to attach but once attached the motor lines up nicely and just snap back the clips, turn the washer over and test with a fresh load.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Allen from Heuvelton, NY
Parts Used:
285753A
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
would not trun the barrel
i had to strip the outer housing of the wahing machine apart the remove the motoe from the transmission to get to the coupling. once i recived the coupling( which was very quickly) i just reversed those steps.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
derrick from paterson, NJ
Parts Used:
285753A
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set
Direct Drive Motor Coupling
Hello the installation was real simple I first uplug machine from wall I turn off all water leading to in to the machine I then tip machine on it side I then took loose all wiring leading to the motor then motor is held up with 3 screws and 2 bands that hold it in place I reinstall the new motor coupling insert the wires and turn back on the water leading to machine then plug machine back in, every thing was good to go. . . . Save a lot of money doing it my self so simple to do. . . .
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Gray, KY
Parts Used:
285753A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Agitator would not work, pump works.
Unplug washer. Place large old towel in floor at rear of washer. Turn off and disconnect water supply lines and allow to drip dry. Place towel in floor in front of washer. Tip washer forward onto face of washer. Unplug wiring clip connector from drive motor. Remove 2 1/4 inch head screws from spring clips on bottom of motor housing. Slowly rotate clips out of the was to drop motor. Knoch top coupling piece off agitator shaft with screwdriver and light hammer. replace coupling with 5/8 deep well socket as a driver which will fit the metal insert in the coupling and not interfere with the shaft. then drive the other coupling onto the motor shaft using light hammer and drive socket(5/8) deep well. place the rubber shock connector onto the agitator drive piece then slide the motor back into the mount position. rotate the clips vback into place. tighten 1/4 head screws in clips re-attach the wiring harness tip the washer back up onto "feet" re-attach water supply lines tighten appropriately. Plug unit into receptacle and enjoy....
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from BIRMINGHAM, AL
Parts Used:
285664
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Old outgoing water hose leaking
1. Need mop, bucket to catch leftover water in machine before you remove old hose. 2. Removed old hose by removing clamp. 3. Dried up any remaining water around fixture before attaching new hose. 4. Slide clamp to bottom of hose before attaching to machine. 5. Attached hose and clamp to machine where old hose was removed from. Make sure clamp is secure. (Please note that clamp that came with the new hose was too big. I used the old one. Worked perfectly). 6. Finally run a little water in you washer, then run out to test tightness and there is no leaks.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dianne from WALES, MI
Parts Used:
80040
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Washer not agitating
Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ramona from MESA, AZ
Parts Used:
80040
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Water drained but would not spin.
Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carl from MILWAUKEE, WI
Parts Used:
285753A
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The tub was not agitating or spinning.
I went to Youtube, looked up motor coupling repair for a Kenmore/Whirlpool washer. Chris Fix had an easy to follow video. I tilted the machine back, propped it up. Removed four clips holding two parts in place. Replaced the faulty coupler, Set the engine back in place replaced the clips, and was finished for a total price of $18.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Hopkins, MN
Parts Used:
285751
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
agitator stopped working properly
Take out softener dispenser. Then take off sealing cam that sits over the cams. Removed center bolt for the agitator and pulled assembly out. Installation was in reverse order.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
randy from overton, TX
Parts Used:
285751
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
top wont agitate
removed top of agitator, used an extenison with a 7/16 socket, removed 1 screw, pulled out cam and only replaced the dog ears. put back together and now it WORKS LIKE NEW. (knock on wood)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Virginia from SNELLVILLE, GA
Parts Used:
285664
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Old drainage hose had a break in it.
Removed broken hose and replaced with new hose. My washer will be 21 years old in January.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from ALBUQUERQUE, NM
Parts Used:
80040
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Agitator not moving
Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11088732795
106 - 120 of 946