11088732795 Kenmore Washer Dryer Combo - Instructions

pop the cap off the top of center agitator unit, remove one 11mm bolt and remove unit from washer. take apart, remove & replace broken dogs and reassemble. I actually bought the wrong kit, my cam is much longer but since the problem was caused by the broken dogs it did not matter.

I ordered a new part based on the exact model number and was sent the wrong part. Fortunately the cam dogs were the same size so I was able to re-use the original housing and throw the new one away.

First I removed the fabric softener cup then the cover with seal. I then used an 11mm socket to remove the bolt, pulled up on the agitator cam removed the old gears and replaced with new ones. Put it all back together and it Works great

Purchased and installed PS1485646 COUPLING, MOTOR (Direct Drive Coupling). We googled "Washing Machine making a grinding noise. Several people suggested coupling probably broken. We located some instructions online regarding dis-assembly, sure enough,the coupling was broken. We ordered the part from Partselect.com. It arrived in three days, replaced the broken coupler. Washing machine back in business for around $20. Hooray! Thanks, Partselect!

Disconnected power, all hoses. Tilted washer backward to see underneath. (Placed sturdy 6" high object under back of washer to keep it from going flat on ground and possibly damaging hose connects). Looked for area where motor and transmission connect. Saw broken part (coupling). After trial and error, figured out how to remove pump and then motor, by removing strap type holding clips, and then broken part was accessible. Ordered part online and was easy to install and reassemble washer now that I knew how it came apart. If I had known the part name or number beforehand, I could have watched the replacement instruction video on this site, but I figured it out anyway, and I did it without removing the whole control switch panel and side panels/body of washer, like they do in the video. But..I guess they had to do that to give you a good view of all the parts and things they were removing underside. I recommend watching video for this part install,so you see what needs to be removed and how underneath, but then just tilting washer back to access underside, without all that control panel and sides removal.

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems

The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.

I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

Direct drive, no belt. Motor sounds like it's spinning but the agitator is not. Bought the coupling (that goes between the motor and the transmission) and replaced it in less than 15 minutes. Two screws and two clips to open the cover. Two clips to move the water pump out of the way. Two screws and two clips to take out the motor. Replace the coupling and reverse the steps.

Remove metal cover; remove pump, remove motor, remove tub spin assembly; remove transmission. Remove clutch be removing retaining ring. Installation was reverse. No problems, part worked like champ.

Note: Called Sears to see if I could get the part locally. Turns our I had to call an 800 number. Lady said that the part was not carried and would have to be shipped from warehouse. Tried to sell me some discharge hoses. Then said the part would cost $65 before S&H. Told her I didn't want to spend that much, she asked how much I wanted to spend and seemed upset when I told her your price. She didn't comp it, just said that theirs was an official part from Sears, blah, blah, blah. Anyway, thanks for the great service!

Disconnect power & water then drain hoses.
We flipped the washer on it's side to gain access to the bottom. There was no need to take off the back panel. Keep a 5 gallon bucket and a few rags handy for the extra water in the pump line.
Disconnected the wiring harness. Removed the brackets holding the motor. It's a little tight on the back bracket. It has a 1/4" hex nut on the back side, so I used a 1/4" drive socket (see: small). Removed the bolts holding the gear case (this makes it a lot easier). Disconnected the pump hose and rotated the motor & gear box and pulled forward. This gives you access to the coupling. Remove the broken part. Clean the area for debris. NOTE: each part of the coupling has 3 fingers (these are what breaks off), so check to make sure you get all broken parts. Insert the new coupling. It has 3 parts; the plastic fittings go on tight and need to be snug to the shaft. Use a screwdriver handle on the center and tap down with a small hammer. Spray silicone on the rubber coupler to allow a little better slide.
Reverse the process. Line the gear box and motor up and push back into the tub assembly. We used 2 people to do this. It's easier to have someone stand over it and hold / rotate the gear box while the other one can align the motor & bolt everything back on.
It took us an hour, however, if you were doing a couple you could get it down to 30 min. flat.
Go wash your clothes!

Woulkd have taken alot less time had I not taken off the control board, back...etc. Laying the unit on its back is perfect. Took it out into the garage when I could have done it in the laundry rooom with very little water loss.
1. Removed all hoses connected to top of motor. This was not very easy since the spring clamps had been in the same place for 20+ years. Also removed all wire harness connected to and from the motor.
2. Removed metal clamps from top of motor unit, and removed the plastic "valve".
3. Removed screws holding in clamps on each side of the motor used to hold motor on motor plate. Removed motor. Trick is to make sure that the back clamp stays in place...makes it a little easier when you go to re install.
4. Cleaned out around agitator shaft, and fitted one side of the coupling and the neoprene type joiner on to the agitator shaft.
5. Fitted other side of coupling on to motor...This is where it got a little tough......and then placed motor unit on the motor plate, making sure to line up teeth to neoprene joiner.
6. Replaced clamps on each side of the motor and screwed in nuts holding them in place.
7. Replaced plastic "valve" and the clamps that hold it in placed...back one is a little tough.
8. Reattached hoses to "valve" and hooked all wire harness back into place.
9.Tested perfect...little burning smell on first spin....but works great now!!

It was a really simple thing to do. Make sure to buy the agitator cam kit (a little piece broke when I was taking it apart). Take off the cover and then the nut that is underneath. Replace the agitator cam and that's it!!! Usually those agitators dog ears wear down with time so if the agitator assembly is not turning, check this first.