11097842700 Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melissa from FOWLER, OH
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer would not heat.
Diagnose that the circuit is functioning up to the igniter. This is done by removing the peep hole cover on the bottom front panel, turn the dryer on and watch for a glowing igniter. My dryer would still ignite the first time because the coils would not show an "open" until they heated up. So if you see the igniter glow it is most likely your coils are bad. Remove two screws from lint trap area on top of dryer. Pry up on top panel at the two clips. Panel is on hinges, so flip it out of the way or just brace it with something enough to keep it off the front panel. Remove the two bolts from inside top corners of the front panel. Use a small punch or screw driver to push in on the tab to release the doors electrical connector. Pull straight up on front panel to remove it from bottom clips. The gas valve is very easy to get to without removing the drum. If needed for inspection or cleaning, just pull back on the belt tensioner to remove the belt from the motor and then pull the drum out. Or just use a stubby phillips screw driver to remove the bracket from the top of the ignition coils. Use a very small flat head screw driver to lift the locking tab on each electrical connector while removing. Remove the coils and place new ones in very same position (note the tab or key way of the coils faces up and are defined in the bracket). Re-assemble all parts making sure connections are tight and drum is correctly mounted. Note: if you remove the drum, return the belt back, in a loop, through the tensioner. This part hurt my head for a moment because I did not pay attention. Also a good idea to vacuum the debris and lint while your in there! As always check to make sure the exhaust pipe is clear. Have fun!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from HUDSON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
I followed your short video and found it very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from ENDICOTT, NY
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from RIVERSIDE, CA
- Parts Used:
- 279834
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Igniter works, valves open, gas Ignitestation then shuts off
All the videos said the same thing. If the Igniter works and the gas ignites bit shuts off soon after that, then the coils are bad. I bought the coils and it didn't fix the problem. My bad, I should have put my meter on it to test it before I bought the part and waited a week to get the coils. Now I'm in the process of illuminating the sensors. I will figure it out. Make sure you use the meter. It will save you the headaches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from glenford, OH
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch was cracked
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this instruction helpful to you?
Thank you for voting!
igniter wold come on for a second then shut off no flame
removed the two screws that hold the coils in place pulled the coils terminal connections off removed and replaced with new coils reattached quick disconnect terminals dryer now works better than when it was new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neal from BRADENTON, FL
- Parts Used:
- WP3362952
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken anchor piece
Installed long end first and snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from St. Augustine, FL
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would not stay closed
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Plainfield, IN
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Gas dryer would not ignite.
I removed two wires from the coil valves. Then I removed two screws from the bracket that holds the coil valves in place. I removed the faulty coil valves and replaced them with the new ones. Put the bracket back on and replaced the two screws and wires. It took almost 5 minutes. The dryer is like new once again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Glendale, CA
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer flame would light then would not ignite again
I used a socket to take of the front cover. I used a screwdriver to remove the two screws that held the coils in place. Replaced the coils and put everything backs together. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from butte, MT
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
would ignite but not run for more than 10 min.
Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vernette from sprague, WA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door catch broke therefore dryer door would not close
just put the new part in the door---sooo easy! THANK YOU!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Tyler, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door wouldn't catch, catch was broken
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Oakland, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
door latch broke
Pop out the old latch and replaced with a new one
Was this instruction helpful to you?
Thank you for voting!